Tabla de contenido
Idiomas disponibles
Idiomas disponibles
SYMBOLS
Read the manual
Warning
Double isulation
Wear eye protection
OPERATING INSTRUCTION
Always make sure the power tool is isolated from the power supply before fi
Always make sure the fixed handle is secure before any job takes place as a loose handle could invite injuries.
Switching the chisel on/off
The chisel has an On/Off switch built in to the handle. Holding the chisel with both hands simply
squeeze the trigger and the motor will start. To switch off release the trigger.
WARNING
The electric hammer chisel con
for a few second a er the trigger has been release, be careful when
own.
pu
1. Clean tools and grease with a thin layer of machine grease before installing.
2. Pull back bit release collar and hold it .
3. Insert the chisel into the nose of the tool.
6. Release the collar again in order to lock the tool.
7.Check the latching by pulling the tool.
Do not use the chisel un you are sa sfied the bit is secured. This electric hammer chisel does not have
reverse dir
ways take care not to force the chisel in case the chisel bit gets stuck. Always make
sure you keep the chisel going in and out to remove debris. This chisel does not have torque facility. It is
not recommended to use any other bit other than masonry or chisels do not use metal cu
could cause serious injury NOTE: chiseling for an ext
overheat. If the chisel gets hot, stop chiseling and allow it to cool for at least 15 minutes. Prec
using electric hammer chisel.
1. Before using the electric hammer chisel always makes sure the oil supply is to the full level and the
scre
ht.
2. This electric hammer chisel has a fixed handle always make sure the screws holding the handle are
secure before opera
takes place. Always use both hands when using this chisel failure to adhere to this
could invite injuries.
3. Safe opera
ways make sure you have a stable posture and safe f
hammer chisel.
4. When working at a high level, always make sure that no person or persons are below you, as this could
invite injuries to those persons under you.
5. Before st
ny job like breaking, chipping a wall, floor or ceiling, thoroughly confirm that no items
such as an electric cable, water pipe or conduit are buried inside as this could cause injury or flooding.
6. Properly set the bit holder.
7. The bit can become very hot during opera
8. Always wear prot
ve safety glasses
4
Wear ear protection
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Disconnect from power supply while
maintance
ny a achment
ay cause the chisel motor to
efore opera
exercise extreme c
could cause injury.
GB
9. Always wear ear defenders or earplugs
10. Always wear suitable dust mask
11. Always wear prot
12. Always wear hardhat
Informa
Prior to opera
1. Power source Ensure that the power source t
on the product nameplate.
2. Power switch Ensure that the power switch is in the o
chisel. If the plug is connected to a power receptacle while the power swit
power tool will start opera
3. Extension cord.
When the work area is away from the power source, use an extension cord of sufficient thickness and rated
capacity. The extension cord should be kept as short as pr
How to use the electric hammer chisel
Place the bit you are going to use to do the job in hand as in Fig 2
(1) Pull the trigger switch a
Handle.
(2) It may be necessary to punch the bit agains
stroke. This is not due t
striking is working.
(3) B
can eff
vely control the subsequent rec
Proceed at a moderate work rate; the use of too much force will impair efficiency.
CAUTION
Some
tool does not begin the striking stroke even when the motor rotates this may be because
the oil has become thick
Due to low temperature or has been standing idle for long period. Run the chisel for approx 5 minutes to
bring the oil tempe
CLEANING AND MAINTENANCE
It is recommended that tools with gears be degreased with a special gear lubricant at every brush change
follows. Run the tool for several minutes to warm it up. Switch the tool off and unplug the main plug from
allow the old grease to collect inside the crank housing. Wipe out the old grease inside and replace with
Maint
When using dull tool bits this can cause motor malf
with new ones without delay when abrasion is noted.
Regularly inspect all moun
screws be loose, re hten them immediately. Failure to do so could result in serious injury.
3. Maintenance of the motor.
The motor unit winding is the very "heart" of the power tool. Exercise due care to ensure the winding does
ve footwear.
ow to use the electric hammer chisel
zed conforms to the power requirements specified
ately this could invite serious injury.
cable
t
tool, it means that the safe guard mechanism against no-load
weight of the machine and by firmly holding the hammer chisel with both hands, one
rature up.
tool
and degraded efficiency. Always replace dull bits
n
rews
rews and ensure that they are pr
GB
efore any work is carried out on the
forcibly in order to begin the striking
htened. Should any of the
5
Tabla de contenido
