Dmx Linking; D-Fi Usb Connectivity - Chauvet DJ SlimPAR H6 ILS Guía De Referencia Rápida

DMX Linking

The SlimPAR H6 ILS can work with a DMX controller. Instructions for connecting and configuring this product for DMX
operation are in the User Manual. If you are not familiar with DMX, download the DMX Primer from www.chauvetdj.com.
Starting Address
To ensure full access to all channels available in each DMX mode, the highest recommended DMX address is 501.
Master/Slave Connection
The SlimPAR H6 ILS uses the DMX data connection and ILS for its Master/Slave mode. Information about configuring the
SlimPAR H6 ILS for Master/Slave operation is in the User Manual, which is available from the Chauvet website.
ILS Connection
The SlimPAR H6 ILS uses the DMX data connection and the D-Fi USB for wireless connection to the Integrated Lighting
System (ILS) ecosystem (patent pending). For more information about configuring the SlimPAR H6 ILS into ILS mode,
please refer to the User Manual available at www.chauvetdj.com.
IRC-6
The SlimPAR H6 ILS can be operated with the CHAUVET Infrared Remote Control (IRC-6). For more information about
the IRC-6, download instructions for the IRC-6 or the SlimPAR H6 ILS User Manual from www.chauvetdj.com.

D-Fi USB Connectivity

The SlimPAR H6 ILS is able to become a D-Fi wireless receiver/transmitter with the use of the D-Fi USB from CHAUVET
DJ. Simply set the DIP switch D-Fi receiving/transmitting channel, plug it into the USB port then set the product's DMX
Personality and DMX Address. Further instructions for connecting and configuring this product for D-Fi USB operation
are in the User Manual.
WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so may cause
damage to the product.
Once plugged in, the D-Fi USB will take over the product. Wired DMX and manual display control/menu
buttons will be unavailable until you unplug the D-Fi USB. The priority levels are:
1. D-Fi USB
2. Wired DMX
3. IRC-6 Remote Control
4. Manual Digital Display/Menu Buttons
Master/Slave Mode (D-Fi USB)
The D-Fi USB allows a single SlimPAR H6 ILS product (the "master") to control the actions of one or more
SlimPAR H6 ILS products (the "slaves") without the need of a DMX controller or DMX cables. The master (transmitter)
product will be set to operate in standalone mode, while the slave (receiver) products will be set to operate in DMX mode.
Once set and connected, the slave products will operate in unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 9-Ch shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to set the starting address to d 1.
4. Press <ENTER>.
5. Set the D-Fi USB to receive on a specific channel, 1–16.
6. Plug in the D-Fi USB.
7. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to operate in standalone mode.
2. Set the D-Fi USB to transmit on the D-Fi channel the slaves are receiving on.
3. Plug in the D-Fi USB.
• All products must be set to the same DMX personality, DMX address, and D-Fi channel.
• Configure all the slave products before configuring the master to transmit.
• Never connect a DMX controller to a D-Fi channel configured for Master/Slave operation
because the controller may interfere with the signals from the master.
SlimPAR H6 ILS QRG Rev. 3
QUICK REFERENCE GUIDE
EN
4