Silverline 996048 Manual De Instrucciones página 9

Installing a charged Battery
1. To fit a charged Battery (7), slide it onto the Battery Mount (5) (Fig. I (c))
Note: The Battery will fit only in one direction, which is determined by its shape and the design
of the Battery Mount. However, if the Battery does not slide onto the Battery Mount easily, do not
force it. Instead, pull the Battery off the Battery Mount again, check for correct position, and try
again gently.
2. Push the Battery onto the Battery Mount until it locks into place securely
Setting up the Charger
1. If fitted, remove the Battery (7) from the Battery Charger (12) (Fig. II (b))
2. Connect the Battery Charger to the mains power supply
Note: The Green LED (14) on the Battery Charger will illuminate to indicate that the Charger
is powered.
WARNING: The Battery Charger is designed for indoor use only and must not be exposed to
moisture and rain.
Charging the Battery
WARNING: Failure to follow the correct procedure when charging the Battery (7) will result in
permanent damage.
Note: Normal charging time is 1 hour for a recently fully-discharged Battery, but if the Battery has
been left in a discharged state for some time, it may take extended time to charge.
1. Slide a discharged or partially discharged Battery onto the Battery Charger (12) (Fig. II (a))
Note: Make sure the Battery and Battery Charger are lined up correctly. If the Battery does not slide
onto the Battery Charger easily, don't force it. Instead, remove the Battery, then check that the top of
the Battery and the Battery Charger slot are clean and undamaged and that the Charger Terminals
(15) are not bent.
2. Once charging commences, only the Red LED (13) will illuminate
Note: If the Red LED is not constantly illuminated after an uncharged Battery is inserted into the
Charger, the Battery or Charger may be faulty. Recheck the Battery is fully inserted in the Battery
Charger. If the fault persists do not use and contact your authorised Silverline distributer.
3. When the Battery is fully-charged, only the Green LED (14) will be illuminated
Battery Charge Level
The Battery has a built-in Battery Charge Indicator (6). Pressing on the button to the right will
indicate the charge level. The number of bars that illuminate when the button is pressed indicate
the charge level; 1 bar indicating a low charge, 3 bars indicating a full charge.
IMPORTANT: When a low charge level is indicated, be aware the tool may stop operating while
in use. This may be dangerous. It is recommended to always ensure the Battery has a good
charge level.
Notes about battery charging
IMPORTANT: Batteries are an expendable supply whose capacity shortens over time. Always adhere
to the correct handling and charging instructions in the manual. If the battery does not hold charge
or working time is shortened, purchase a genuine Silverline replacement.
• The battery should be charged at ambient temperatures between 10°C and 40°C (ideally
around 20°C)
• After charging, allow 15 minutes for the battery to cool before use
• Ensure that the charger is disconnected from the mains supply after use, and is stored correctly
• Do not leave batteries on charge for extended periods and never store batteries on charge
• The charger monitors battery temperature and voltage while charging. Remove the battery once
charging has been completed to maximise charge cycles of the battery and not waste power
• Batteries can become faulty over time, individual cells in the battery can fail, and the battery
could short. The charger will not charge faulty batteries. Use another battery, if possible, to check
correct functionality of the charger and purchase a replacement battery if a faulty battery
is indicated
• Do not store Lithium-ion battery packs in a discharged state long term. This can damage the
Lithium-ion cells. For long-term storage, store batteries in a high charge state disconnected from
the power tool
• The capacity of batteries will reduce over time. After 100 charge cycles, the battery's operation
time and the performance will slightly reduce. This decline will continue until the battery has
minimal capacity after 500 charge cycles. This is normal and not a fault with the battery pack
Fitting a driver bit
WARNING: DO NOT fit any attachment with a maximum speed lower than the no load speed
of the machine.
Refer to Fig. III
1. Pull the Collar (2) of the Hex Bit Holder (1) forward
2. Insert the bit
3. Release the Collar
4. Pull on the bit to check that it is securely fitted. If the bit is not secure, repeat steps 1 to 3
Note: Make sure driver bits are suitable for use with an impact driver.
Operation
WARNING: ALWAYS wear appropriate personal protective equipment, including eye protection
and gloves when working with this tool.
Direction control
IMPORTANT: NEVER change the direction of rotation while the tool is running. This may cause
permanent damage to the tool.
• Use the Direction Switch (4) to change the direction of rotation
• For anti-clockwise rotation, push the Direction Switch to the right
• For clockwise rotation, push the Direction Switch to the left
Note: When the Direction Switch is in the central position, the tool is locked and cannot be switched
ON. Use this setting as a safety feature to prevent the tool from being switched ON accidentally.
Switching ON & OFF
WARNING: Always wear adequate personal protection equipment when setting up and
operating this tool.
1. Select a direction of rotation using the Direction Switch (4)
2. To start the tool, squeeze the ON/OFF Switch (9)
3. The speed of the tool is controlled by the movement of the trigger: the further the trigger is
pressed down, the faster the drill will run
4. Release the ON/OFF Switch to stop the tool
Note: A LED Light (11) will operate each time the ON/OFF Switch is pressed, to illuminate the
work area.
Note: The On-Tool Battery Indicator (10) will operate each time the ON/OFF Switch is pressed.
The number of bars that illuminate when the button is pressed indicate the charge level; 1 bar
indicating a low charge, 3 bars indicating a full charge.
WARNING: If the power tool gets excessively hot in use, stop using the tool immediately and
allow to cool before continuing work. The cooling period can be reduced by operating the impact
driver at maximum speed with no load. Always make sure the Motor Vents (3) are not blocked and
do not allow dust to enter the body of the tool through the Motor Vents; dust, especially metallic
dust, may damage or destroy the tool.
Accessories
• A full range of accessories including impact driver bits is available from your Silverline stockist
• Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: Always disconnect the tool from the power supply, before cleaning or carrying
out maintenance.
General inspection
• Regularly check that all the fixing screws are tight. They may vibrate loose over time
• Repairs should be carried out by an authorised Silverline service centre.
Lubrication
• Lubricate all moving parts with a suitable lubricant spray, at regular intervals
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the device's service life
• Clean the body of your tool with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent
on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes
(where applicable)
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
• If you suspect that the brushes may be worn, have them replaced at an authorised service centre
silverlinetools.com
18V Impact Driver
9