Phormalab AURA AAA01 Manual De Instrucciones página 19

EN – ASSEMBLY INSTRUCTIONS
Assembly heating appliance AURA with attachments
AAA01 e ABA01
Warning: the AURA heating appliance must be mounted and oriented at a
safe distance from walls, or flammable objects. Follow the instructions
contained in the instruction booklet of the AURA heating appliance.
1. Package contents
A. AURA heating appliance
B. Support Joint
C. Wall plate
D. Round lid
E. Two M6 screws
F. Two M5 screws
G. Two M6 grains
WALL MOUNTING KIT
H. Short tube
I. Wall attachment joint
CEILING MOUNTING KIT
C. Tube for ceiling attachment
D. Ceiling attachment joint
E. Two M4 screws
Choose the position where you want to install the AURA heater:
if you choose WALL mounting, use the mounting kit with the word WALL
and follow the instructions from point 2 to point 7
if you choose CEILING mounting, use the mounting kit with the word
CEILING and follow the instructions from point 8 to point 13
WALL MOUNTING ASSEMBLY AAA01
2. Insert the tube H on the support joint B. Take the screws and place
them on the back of the plate C (the screws are housed in the seat
created inside the plate). Fix the screws E to the support joint B using the
special key found inside the box.
3. Fix plate C to the wall at the desired height using two suitable
expansion plugs (not included). Once the attachment is fixed to the wall,
cover with the round lid D and fix it on the plate using the two grub screws
G.
4. Take the lamp body A, place it inside its seat in the support joint B and
close using the joint for wall attachment I. Secure the two joints using the
The lamp must always be connected to an electrical system that
supports the 2000W power of 2000W. Check with the installer that
your system is adequate to support this power.ttenzione: two screws
F.
5. ATTENTION: Check the correct installation of the lamp, the lines on
the wall attachment joint and on the attachment of the AURA heating
device (A) must be aligned. Otherwise, remove the lamp in step 4 and
repeat the operation.
6. Orient the lamp A in the desired direction and finally tighten the screws
F. Connect the lamp to the electrical system.rientare
7. The power cable must be kept away from the lamp body, to facilitate
this situation, use the velcro strip inside the box and fix the cable to the
JOINT. The AURA lamp is now assembled and ready for use.
Attention: The lamp must always be connected to an
electrical system that supports the 2000W power of
2000W. Check with the installer that your system is
adequate to support this power.ttenzione:
CEILING MOUNTING ASSEMBLY ABA01
8. insert the tube L on the support joint B and fix it using the two screws
N. Take the screws E place them on the back of the plate C (the screws
are housed in the seat created inside the plate). Secure the screws E to
the support joint B using the special key found inside the box.
REV. 02 – 08/2021
9. Secure plate C to the ceiling using two suitable expansion plugs (not
included). Once the attachment is fixed to the wall, cover with the round
lid D and fix it on the plate using the two M6 grub screws (G).
10. Take the lamp body A, place it inside its seat in the support joint B
and close using the joint for ceiling attachment M. Secure the two joints
using the two screws F.
11. ATTENTION: Check the correct installation of the lamp, the lines on
the wall attachment joint and on the attachment of the AURA heating
device (A) must be aligned. Otherwise, remove the lamp in step 10 and
repeat the operation.
12. Orient the lamp A in the desired direction and finally tighten the
screws F. Connect the lamp to the electrical system.rientare
13. The power cable must be kept away from the lamp body, to facilitate
this situation, use the velcro strip inside the box and fix the cable to the
JOINT. The AURA lamp is now assembled and ready for use.
Attention: The lamp must always be connected to an
electrical system that supports the 2000W power of
2000W. Check with the installer that your system is
adequate to support this power.ttenzione:
Urbani srl reserves the right to all the changes to improve the products also during sales
______________________________________________________
DE - MONTAGEANLEITUNG
Montage des Wand/Decken-Heizstrahlers AURA
AAA01 und ABA01
Achtung: Der Heizstrahler
Sicherheitsabstand zu Mauern,
Gegenständen montiert und ausgerichtet werden. Folgen Sie den
Hinweisen in der Gebrauchsanleitung für den Heizstrahler AURA.
1. Lieferumfang:
A. Heizstrahler AURA
B. Traggelenk
C. Wandplatte
D. Runde Abdeckung
E. Zwei Schrauben M6
F. Zwei Schrauben M5
G. Zwei Gewindestifte M6
MONTAGEKIT ZUR WANDBEFESTIGUNG
H. Kurzes Rohr
I. Verbindungsstück zur Wandbefestigung
MONTAGEKIT ZUR DECKENBEFESTIGUNG
L. Rohr zur Deckenbefestigung
M. Verbindungsstück zur Deckenbefestigung
N. Zwei Schrauben M4
Wählen Sie die Stelle, an der die Heizlampe montiert werden soll:
WANDBEFESTIGUNG
Für die
WALL
der Aufschrift und folgen den Schritten
DECKENBEFESTIGUNG
Für die
CEILING
mit der Aufschrift und folgen den Schritten
WANDBEFESTIGUNG AAA01
2.Setzen Sie das Rohr H auf das Traggelenk B. Nehmen Sie die
Schrauben E und setzen Sie sie auf den hinteren Teil der Platte C (die
Schrauben passen in den im Inneren der Platte befindlichen Sitz). Ziehen
Sie die Schrauben E am Traggelenk B fest. Nutzen Sie dafür den
entsprechenden, der Packung beigefügten, Schraubenschlüssel.
3. Befestigen Sie Platte C in der gewünschten Position an der Wand.
Verwenden Sie dafür drei entsprechend geeignete Spreizdübel (nicht im
AURA muss mit ausreichendem
Wänden und entflammbaren
verwenden Sie das Montagekit mit
2 7.
bis
verwenden Sie das Montagekit
8 13.
bis