Tabla de contenido
Idiomas disponibles
Idiomas disponibles
3.
Battery packs marked with CAS are 100%
compatible with CAS devices (Cordless
Alliance System).
4.
Tighten blade retaining bolt and all clamps
before operating.
5.
Secure work piece properly. Work piece should
be straight and firmly clamped to avoid
possible movement and pinching as the cut
nears completion.
6.
Allow the blade to come to a complete stop
before removing or securing workpiece, or
changing workpiece angle.
7.
Check the inside surfaces of the arbor flanges
as well as the sides of the blade for freedom
from any foreign matter.
8.
Check the blade for cracks or other damage
before operation. Replace cracked or damaged
blade immediately.
9.
Never start the tool with the work piece
against the blade.
10. Allow the motor to achieve full speed before
cutting.
11. After turning tool "ON", gently push the tool
forward to engage work piece, then slowly
increase pressure as required to produce the
least amount of "sparking".
12. Important: After completing the cut, release
power switch and wait for coasting blade to
stop completely before putting the saw down.
13. Never operate the tool in an area with
flammable solids, liquids, or gases. Sparks or
hot fragments could cause a fire or explosion.
14. This tool is designed for ferrous metals
only. Do not attempt to cut wood, masonry,
magnesium, or any other pyrophoric materials
with this tool.
15. Do not use cutting fluids or lubricants on the
blade.
16. Some metals have coatings, which can be
toxic. Take extra care to prevent inhalation
and skin contact when working with these
materials. Request, and follow, any safety
information available from your material
supplier.
17. There are certain applications for which this
tool was designed. The manufacturer strongly
recommends that this tool NOT be modified
and/ or used for any application other than
for which it was designed. If you have any
questions relative to its application DO
NOT use the tool until you have written the
manufacturer and have been advised.
10
Metal chips are often very sharp and hot. Never
touch them with bare hands. Clean up with a
magnetic chip collector and a chip hook or other
appropriate tool.
6. FUNCTIONAL DESCRIPTION
This machine is a dry cutting circular saw designed
to cut ferrous metals, which uses carbide tipped saw
blades. The saw should only be used with original
Jepson Power saw blades.
6.1.
UNPACKING
Carefully remove the tool and all loose items from
the shipping container. Retain all packing materials
until after you have inspected and satisfactorily
operated the machine.
6.2.
CARTON CONTENTS
1.
Metal cutting saw HDC 8203E
2.
Original Jepson Power carbide tipped LBS saw
blade 203/48T
3.
2x 18V LiHD 5.5A high-performance battery
4.
Air-Cooled LiHD charging station
5.
Rip fence cutting guide
6.
Hex wrench
6.3.
CHARGING THE RECHARGEABLE
BATTERY
Check
whether
the
rechargeable battery agrees with the information
specified on the machine.
Rechargeable battery and charger are matched to
each other. Only use the Jepson Power Air-Cooled
LiHD chargers for recharging.
Before using a new machine, first of all charge the
rechargeable battery.
A description of how to start up and charge the
Jepson Power Air-Cooled LiHD charger can be
found in the appended instructions "Jepson Power
Air-Cooled LiHD charging station".
The rechargeable battery is equipped with a
temperature monitoring system. This guarantees
that the rechargeable battery is only charged in
the temperature range between 0°C and 50°C. This
achieves a long service life for the rechargeable
battery.
A considerably shortened operating time per
charging procedure indicates that the rechargeable
battery is spent and needs to be replaced.
ENGLISH
rated
voltage
of
the
Tabla de contenido
