En / En-Us; Jungheinrich Wmt 210 / 215; Operating Instructions - Jungheinrich WMT 210 Manual De Instrucciones

EN / EN-US

Jungheinrich WMT 210 / 215

Operating Instructions

1. Correct Use
The Jungheinrich truck terminals WMT were specifically
developed for use on forklift trucks in logistics and industrial
environments.
The terminal must be operated and stored under the
following conditions:
Temperature during operation
Temperature during storage
to +80°C
Air humidity in operation and storage 10% to 95% without
condensate
The terminal is protected against dust and jets of water in
accordance with protection rating IP65.
Use in areas where there is a risk of explosion is prohibited.
2. Type plate
The type plate on the back of the terminal contains
information about, among other things:
The configuration identification (figure I, position
1)
Serial number (figure I, position 2)
WLAN MAC address (figure I, position 3)
3. Installation of the Grab Handle
WARNING!
Installation work on the terminal may be performed only by
suitably trained electricians when the terminal has been
secured and disconnected from the power.
Install the grab handle (Figure II, item 6) on the terminal
using the screws supplied in the following sequence from the
inside outwards:
Nord-Lock washer -> Bracket -> Nord-Lock washer -> Allen
screw (6 mm Allen key) -> Protective cover
3.1 Installation of VESA Support
Alternatively, the terminal can be installed using the VESA
75-hole pattern (Fig. II, item 4) with a suitable support, e.g.
RAM Mount.
Thread: M6 / torque: recommended 8 Nm
Max. screw-in depth in the threaded bushings: 6 mm
Note
The relevant safety measures must be observed at all times
when handling electrostatically hazardous components. (DIN
EN61340-5-1 / DIN EN 61340-5-2).
When selecting the mounting position, possible restrictions
of the driver's field of vision and safe driving operation must
be taken into account.
4. Installation
4.1. Opening the service chamber
Remove the screws from the service chamber cover (Fig. II,
item 5) using a Torx Tx20 screwdriver. Lift the cover from the
left and pull off.
4.2. Connection of the Cables
Connect all required cables within the service chamber. Use
the grommets (Fig. III, item 9) to ensure the IP65 protection
rating. The grommets have a slot on the side for inserting the
cables.
4.3. Connection of the Power Source
The terminal is supplied via a 4-pin connector (Phoenix
Contact MC 1.5/ 4-STF-3.81) with 12 V to 48 V DC (Fig. III,
item 7).
© Jungheinrich AG, Friedrich-Ebert-Damm 129, 22047 Hamburg
1: Functional Earth 2: 0 V DC 3: Ignition (+12 to 48 V DC) 4:
Earthing to the truck chassis is via 2x1.5 mm² flat-plug
Caution!
-30°C to +50°C
The protective conductor must always be attached.
-40°C
Without the protective conductor, there is a risk of overvoltage
at the terminal.
The power supply must be equipped with a fuse:
7 A for 12 V DC; 4 A for 24 V DC; 2 A for 48 V DC.
Applying a voltage to the ignition contact automatically
switches on the vehicle terminal.
Once the work is complete, the removed service chamber
cover needs to be reinstalled on the terminal with the screws.
Make sure that the grommets (Fig. III, item 9) are in the
correct position during installation.
5.
Once the terminal has been connected to the power source
and the service chamber has been re-sealed, the terminal
can be commissioned.
To do this, press the Power-On button on the front for
approx. 1 second (Fig. IV, item 10).
Note
To avoid condensation water, the terminal must not be
switched on until it has adjusted to the room temperature.
If the terminal shows obvious signs of damage, caused e.g.
by incorrect operating/storage conditions or improper use, it
must be taken out of commission immediately and secured
against inadvertent recommissioning.
6.
Note
To clean the touch screen use a dust-free cloth slightly
moistened with cleaning agent for TFT displays.
For wet cleaning use a commercially available glass cleaner
with a low alcohol content.
7.
The terminal (apart from the service chamber) must not be
opened by personnel not authorised by Jungheinrich; action
to the contrary will invalidate the warranty.
8.
You can find more information about configuration and
operating the terminal at:
9.
Jungheinrich Aktiengesellschaft hereby declares that the
aforementioned radio equipment satisfies Directive
2014/53/EU.
The full text of the EU Declaration of Conformity is available
at the following address:
+12 to 48 V DC
contacts (Fig. III, item 8).
4.4. Close the Service Chamber Cover
Switching on the Terminal
Cleaning
Opening the Terminal
Support and Manual
https://support-rdt.jungheinrich.com/
SIMPLIFIED EU DECLARATION OF CONFORMITY
www.jungheinrich.com/declaration-of-conformity
v1.0
Public
3