LUND 67860 Manual Original página 15

After pressing "MANUAL" button it is possible to input the following parameters: blade rotational speed, temperature, operation
time. You can change parameter setting with the knob, and you can select another parameter by pressing "MANUAL" button.
To program the time of operations, firstly press the button to set minutes and then press the button to set seconds.
To bypass any parameter and select the next parameter just press "MANUAL" button.
To start product operation press "START/PAUSE" button. When in auto mode you can interrupt operation and restore operation
in the same manner.
The end of operation is indicated with repeated sound signal. To turn the sound off press "STOP" button. The sound signal will
switch off automatically following ca. 1 minute.
Note
Time measurement follows (max. 60 minutes) after manual temperature or rotation speed setting and pressing "START/PAUSE"
button.
Counting down will start, if manual time setting was programmed.
After manual temperature or rotation speed setting and switching on, pressing "MANUAL" button will enable change of pro-
grammed setting: speed, temperature and operation time. Any setting change will be applied immediately.
If heating was activated, maximum permitted rotational speed setting 05.
Food or water placed inside the pot shall not be over 2L or 2kg. Always adhere to limits regarding pot maximum capacity.
Scale Operation
Product is provided with scale that ensures weighing of food products placed inside the pot. After pressing "SCALE" button, and
then reading in grams will be displayed, and scale indicator will start flashing.
For calibration press and hold "SCALE" button for ca. 2 seconds.
Do not use the scale, when engine is in operation– rotation of blades.
Maximum weight of food products is 4000g. If weight is over maximum limit, the display will show "F0FF".
When weighing, the product shall be on stable surface, otherwise readings may be inaccurate.
Do not place into or onto the pot, food products whose weigh is over 6 kg, as it may result in product damage.
Other tips
Do not use the butterfly stirrer when mixing the dough. Do not use the butterfly stirrer for rotational speed setting over 04.
Do not use the butterfly stirrer for auto modes.
When dough mode is selected, the program will not activate, if heater temperature is over 50
Do not program manually settings for dough kneading.
Flour weight shall not be over 500g, and water weight shall not be over 300g.
Continuous operation during dough mixing shall not be over three cycles, and after each cycle at least 5 min. pause is required.
During dough mixing the processor shall be on stable and even surface, at safe distance from edge (of table etc.). Before adding flour, firstly dry carefully the pot to prevent sticking of flour to pot walls. Flour and water mixing ratio is 10 to 6.
Recipes in auto mode
Caution! Completion of each step in the given mode is indicated with sound signal.
Recipe Step Required Activity
1 Put seafood and other products into the pot
Jam
(20 min.)
2 Add sugar and honey and wait until boiling
1 Heat the empty pot
2 Add butter or oil for frying, onion and garlic
Soup
3 Add pumpkin and water
(22 min.)
4 Slicing
5 Add milk, salt grinded cinnamon or other spices
1 Heat the empty pot
2 Add olive oil, onion and garlic
Sauce
26 min
3 Add sliced pork, tomato sauce, vine, chilli sauce, salt and other spices
4 Add seafood
1: 500g of flour and 300g of water
Dough 1
2: in case of high gluten flour the limit is 300g.
Steaming
1
Fish, corn, potatoes etc.
O R I G I N A L
GB
Temperature [ C]
O
0
100
100
100
100
-
100
120
120
100
100
Ambient
100
I N S T R U C T I O N S
C.
O
Time (min) Speed
3 05
17 01
2 00
1.5 01
14 01
3 07
1.5 05
2 00
1.5 01
4 + 5 01
13.5 01
1.5 05/02
60
00
15