Westward Operating Instructions and Parts Manual
7-8
OPERATING
OPERATING
INSTRUCTIONS
INSTRUCTIONS
OPERATING INSTRUCTIONS
OPERATING
INSTRUCTIONS
Read
Read
the
the
entire
entire
SAFETY
SAFETY
INFORMATION
INFORMATION
Read
Read the
the entire
entire SAFETY
SAFETY INFORMATION
INFORMATION section
subheadings
subheadings
subheadings
subheadings therein
therein
therein before
therein
before
before
before using
Use
Use
this
this
tool
tool
for
for
the
the
manufacture' ' ' ' s s s s intended
manufacture
manufacture
Use
Use this
this tool
tool for
for the
the manufacture
manual
manual
can
can
result
result
injury
injury or or or or property
injury
manual can
manual
can result
result injury
Always
Always
Always wear
Always
1. 1. 1. 1.
Select the appropriate punch die set. Ask an authorized facility or distributor to choose proper punch die set for
hole punching.
Do
Do
not
not
Do not
Do
not exceed
failure,
failure,
failure, which
failure,
warning
warning
warning can
warning
2. 2. 2. 2.
Drill a pilot hole¢0.45" by electric drill on the metal sheet, which called pilot hole.
3. 3. 3. 3.
Turn the turn screw counterclockwise to fully extend the ram.
4. 4. 4. 4.
Thread the draw stud completely into the ram.
5. 5. 5. 5.
Slide the spacer in necessary onto the draw stud, and the die after, then let the metal sheet go through the draw
stud by the hole. Last thread the punch facing the steel plate. Make sure the spacer, punch, die and material are
parallel close.
An improper setup could cause the components damaged.
Do not operate the pump after ram motion stops. Continuing to operate the pump lever after
the ram stops will damage the ram. If the ram stops before the hole is complete, stop
pumping, check that the setup is correct and that you have not exceeded the tool's capacity.
See the setup instruction.. if necessary, disassemble the setup and add or remove the spacer.
6. 6. 6. 6.
Pump the handle lever till completely punching
Make sure the punching completely during the operation to avoid the scrap remaining the
down punch.
7. 7. 7. 7.
Turn the screw anticlockwise to release the pressure at the pump.
STEP-UP
STEP-UP
PUNCHING
PUNCHING
STEP-UP
STEP-UP PUNCHING
PUNCHING
The 1/2" conduit-size punch is often used to increase the size of the pilot hole, this is called "step-up punching."
After enlarging the pilot hole, the 3/4" draw stud is used to punch the final hole.
Do not allow anyone to stand in front of the punch or behind the hydraulic ram. Ignore this
warning can result in injury or damage.
All manuals and user guides at all-guides.com
HYDRAULIC PUNCH SET, KNOCKOUT W6 PUNCH, 2
STUDS, 1 SPACER, 1 SEALING KIT
Draw Stud
For connecting cylinder with punch & die
section
section
section at at at at the
the
the
the beginning
using this
using
using
this
this
this product.
product.
product.
product.
intended
intended
purpose
purpose
intended purpose
purpose only.
property
property
damage.
damage.
property damage.
damage.
wear safety
wear
wear
safety
safety goggles
safety
goggles
goggles
goggles during
during
during
during the
exceed
exceed
the
the
rated
rated
capacity
capacity of of of of this
capacity
exceed the
the rated
rated capacity
which
which
which could
could
could throw
could
throw
throw
throw broken
broken
broken
broken parts
can result
can
can
result
result
result injury
injury or or or or death.
injury
injury
death.
death.
death.
beginning
beginning of of of of this
beginning
this
this
manual
manual
this manual
manual including
only.
only.
Use
Use
other
other
than
than
that
that
which is is is is described
which
which
only. Use
Use other
other than
than that
that which
the
the op
the
op
op
operation.
eration.
eration.
eration.
this
this
tool;
tool;
otherwise
otherwise
otherwise it it it it will
will
will
this tool;
tool; otherwise
will caused
parts
parts
parts with
with great
with
with
great
great
great force.
force.
force.
force. Failure
Failure
Failure to to to to observe
Failure
3
13G264
including
including
all
all
text
text
under
under
including all
all text
text under
under
described
described in in in in this
described
this
this
this
caused
caused
caused a a a a component
component
component
component
observe
observe
observe this
this
this
this