Operation - Ryobi P112 Manual Del Operador

WARNING:
Do not allow familiarity with tools to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
APPLICATIONS
You may use this tool for the following purposes:
 Charging compatible Ryobi 18 volt Ni-Cd battery packs
CAUTION:
If at any point during the charging process none of the
LEDs are lit, remove the battery pack from the charger
to avoid damaging the product. DO NOT insert another
battery. Return the charger and battery to your nearest
service center for service or replacement.
CAUTION:
Charge in a well ventilated area. Do not block charger
vents. Keep them clear to allow proper ventilation.
LED FUNCTIONS OF CHARGER
See Figure 2, page 8.
CHARGER LED WILL BE ON TO INDICATE
STATUS OF CHARGER AND BATTERy PACK:
 Red LED on, Green LED off = Power to charger is on.
 Red LED flashing, Green LED off = Battery is being
tested.
 Red LED flashing, Green LED flashing = Battery is
defective.
 Red LED ON, Green LED flashing = Battery is charging.
 Red LED off, Green LED on = Battery is fully charged.

OPERATION

CHARGING THE BATTERy PACK
This charger will accept Ryobi One+ 18 V nickel-cadmium
battery packs.
Use only these Ryobi One+ 18 V battery packs with this
charger:
BATTERy PACK
(P100 Ni-Cd)
130255004, 130224028
Battery packs for this tool are shipped in a low charge
condition to prevent possible problems. Therefore, you
should charge them until the green LED on the front of the
charger comes on.
CHARGING A BATTERy PACK
See Figure 2, page 8.
If the charger does not charge the battery pack under normal
circumstances, return both the battery pack and charger to
your nearest Authorized Service Center for electrical check.
 Use battery pack only with the recommended charger.
 Connect the charger to the power supply. Make sure the
power supply is normal household voltage, 120 volts,
AC only, 60 Hz.
 Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured in the
charger before beginning operation.
 Place the battery pack in the charger aligning raised rib
on the battery pack with the groove in the charger.
 Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts in the
charger.
 Do not place the charger and battery pack in an area of
extreme heat or cold. They will work best at normal room
temperature.
NOTE: The charger and battery pack should be placed
in a location where the temperature is more than 50°F
but less than 86°F.
 The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
 After charging is complete, the green LED will remain
on until the battery pack is removed from the charger or
charger is disconnected from the power supply.
 When batteries become fully charged, unplug the charger
from the power supply and remove the battery pack.
 To remove the battery pack from the charger, depress
the latches on each side of the battery pack.
CHARGING A HOT BATTERy PACK
If the battery pack is above normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery pack cools down to approximately 122°F,
the charger will automatically begin fast charge mode.
CHARGING A COOL BATTERy PACK
If the battery pack is below normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery warms to a temperature of more than
32°F, the charger will automatically begin charge mode.
6 - English
CHARGER (P112)
140127001