Tabla de contenido
Idiomas disponibles
Idiomas disponibles
garment upon or below the cutting area of the disk or
within the cutting path of the disk.
4
Fastening the workpiece to be cut shall not be carried
out manually but with the assistance of pushers, wedgers
and clamps warranting a firm fastening of the workpiece
to be cut under any circumstances (appearance of nods,
etc.). By putting this preventive measure into practice the
risk of contact with the disks during the development of
the operation is practically excluded as it allows hands to
remain distanced from the hazardous area.
5
Always disconnect the machine when leaving it alone.
6
The presence of one or more assistants will be required
for cutting workpieces being longer than 1.5 m.
1.2 Preventing fortuitous contacts with the disk rotating
without load in the resting position
Independently from that the disk, when resting, stays
protected by the safety guards as installed, it is categorically
advised against using the locking switch so as to guarantee
that disk does not rotate without load in the resting position
thereof
1.3 Preventing abrupt falls of the disk due to breakage of
the spring
1
By means of a regular maintenance the machine will
always be in a perfect condition.
2
Check the area and the machine on each working day
and routinely test all movements visually with the machine
disconnected.
3
Check springs and the bearings thereof on each
working, and have them checked periodically by qualified
personnel.
4
Make sure that the head perfectly ascends to its upper
position by the sole action of springs.
5
Check the upper locking system on each working day by
raising the head up to abutment and checking locking and
unlocking by means of button, and have this periodically
checked by qualified personnel.
6
Never expose your hands or any other part of your body
to he cutting path.
7
Never allow the head that holds the disk to remain in an
undetermined position unless the operator is mandatorily
grasping the control grip.
8
For any break between cuttings, however short it may be,
always use the automatic lock of the head in the upper
position by raising the head to the upper stopper.
9
Each time that the machine remains at rest, leave it in the
lower resting position by placing the head at 90º vertical
and 0º horizontal, protecting by means of the stationary
guard and finally locking it by lowering the head and
pushing button.
2. Preventing projections of the cut workpiece
So as to carry out the cutting of workpieces using a
stopper, this latter must be foldable or movable. Once the
operator has selected the cutting range and firmly fixed the
workpiece to the table, he/she will remove the stopper so as
to prevent the workpiece as cut from wedging between the
stopper and the disk.
DUST EXTRACTION
15.
All models are prepared for mounting equipment (not
included) for the aspiration of particles generated during the
cutting operation.
The extraction equipment shall be coupled to the particle
outlet nozzle.
GENERAL SAFETY INSTRUCTIONS
16.
WARNING! When using electrical tools, the essential safety
precautions should always be taken to reduce the risks of
fire, electrical shock and personal damages, including the
following.
Read these instructions with attention before using this
ENGLISH
19
product, and store them.
REGULAR CLEANING, MAINTENANCE AND
17.
GREASING
WARNING! .Desenchufar the plug before performing any
adjustment or maintenance comeback.
Cleaning
Clean the machine starting with a brush or with a flat brush
so as to remove sawdust and with a soft cloth.If compressed
air is available, complete cleaning by blowing with the
compressed air pistol.
Maintenance
After each 2,000 hours of use or each two years the
electrical tool must be sent to the official technical service for
maintenance and complete revision.
Before each use, check nuts and joints to detect any vibration
issues and use. If there are gaps take the machine to service.
Except squeeze and brush change, the machine does not
require any special maintenance by the user. Keep the
machine clean and use it correctly.
Regularly have the correctness of the adjustments checked
by a sufficiently trained user. In the case of any failure, contact
our technical service.
Greasing
This machine does not require any specific greasing by the
user. Specific greasing of the electrical tool will be carried out
on the occasion of the regular maintenance revisions at the
official technical service.
SAFE OPERATION
18.
1
Keep working area clean. Unorderly working areas and
benches are susceptible of causing damages.
2
Take into account the surroundings of the working
area. Do not expose tools to rain. Do not use tools at humid
or wet locations. Keep working area well illuminated. Do
not use tools in the presence of inflammable liquids or
gases.
3
Protect against electrical shocks. Avoid contacts of
the body with earthed or chassis-earthed surfaces (e.g.
pipes, radiators, heaters, refrigerators, etc.).
4
Keep other persons away. Do not allow that other
persons, especially children, who are not linked to the
work, touch the tool or extensible cables, and keep them
away form the working area.
5
Store tools that are not being used. When not in use,
tools should be stored at a dry and closed location out of
the reach of children. Do not place anything on top of the
machine, or store the machine start backwards.
6
Do not force the tool. The tool operated better and
safer at the assigned characteristic for which it has been
designed.
7
Choose the right tool. Do not force a small tool to carry
out the work that corresponds to a heavy tool. Do not use
tools for purposes for which they have not been designed;
for instance, do not use circular saws for cutting the trunks
of trees or the branches thereof.
8
Dress suitably. Do not use loose-fitting garment or
jewellery articles that may get caught by moving parts.
The use of nonslip footwear is recommended for working
at outside locations. For long hair use protective caps.
9
Use safety equipment. Use protective goggles. Use face
protector or mask to avoid dust if the cutting operations
may generate it.
10 Connect the dust-extraction equipment. Should
devices for the connection thereof to dust extraction and
collection equipments be provided, make sure that they
are in fact connected and adequately used.
11 Do not mistreat the cables. Never pull the cable to
disconnect it from the socket. Keep the cable away from
heat, oil and cutting edges.
19
Tabla de contenido
