Refsta AMPERLINK Manual De Utilización página 22

1N 100-240V ~ 50-60Hz
POWER SOURCE
yellow/green - EARTH
blue - N1 IN
black - L1 IN
3N 380-415V ~ 50-60Hz
POWER SOURCE
yellow/green - EARTH
blue - N1 IN
black - L1 IN
brown - L2 IN
grey - L3 IN
Define the type and section of power cables
accepted
WARNING: For the connection use multipolar
cables H05V2V2-F conforming to the following
standards:
- Main standard: EN 50525-2-11
- Conductor: EN 60228; IEC 60228
- Self-extinguishing: EN 60332-1-2; IEC 60332-1-2
PFor single-phase connections, use cables with
sections between 3Gx2.5mm2 and 3Gx4.00mm2.
For multi-phase connections, use cables with a section
of not less than 1.5mm2.
It is mandatory always to connect the conductor of
the NEUTRAL (N) and the EARTH (PE) regardless of the
number of connected phases.
USE
STAGE 0 - Power on
Appena alimentata la scheda l'AMPERLINK emette un
beep lungo
STAGE 1 - Memorizing the remote control with the
AMPERLINK:
To assign the remote control to the AMPERLINK, keep
the P1 key pressed for at least 3s and until you hear
a long beep and the P1 LED flashes. Then within 10
seconds, press the AUX button on the remote control.
If the procedure was successful, a short beep is emitted,
and LED P1 stops flashing.
FASE 2- Memorizzazione AMPERLINK con la cappa:
Assegnazione AMPERLINK AMPERLINK assignment to
HOB
yellow/green - EARTH
blue - N1 OUT
black - L1 OUT
HOB
yellow/green - EARTH
blue - N1 OUT
black - L1 OUT
brown - L2 OUT
grey - L3 OUT
the hood. Press and release the AMPERLINK P1 button;
a short beep is emitted, and the hood light should
change state.
STAGE 3 - Checking the remote control assignment
Per verificare l'assegnazione del radiocomando si può
premere e rilasciare il tasto P1 dell'AMPERLINK; viene
emesso un beep corto e la luce della cappa dovrebbe
cambiare stato. Può essere necessario premere due
volte il tasto P1 per cambiare lo stato della luce
(sempre se la FASE 1 è stata svolta con il medesimo
telecomando).
STAGE 4- Activation of the automatic function:
To activate the automatic function press for at least
2 seconds the key used in PHASE 1; deactivation is
signaled with a long beep, and two flashes of the
P2 led.
CHEME - Algorithm:
The AMPERLINK device is mounted between the
power supply and the hob; in this way, it can measure
the absorption of the hob and sends the appropriate
suction speed via the RF radio module to the hood.
For example, if we turn on at least one area of the
hob, the hood initially turns on at speed 1, and then
at the power absorbed by the hob, the algorithm
progressively brings the hood to the speed deemed
optimal.
If the user turns off the hob, the speed gradually
decreases until the hood will set off.
If during this time, the user switches on an area of the
hob again, the algorithm starts controlling the hood
still by sending the appropriate speed.
If, during automatic operation, the user presses any
button on the push-button panel or radio control,
the automatic mode is suspended until AMPERLINK
recognizes a change in the power absorbed by the
hob and gives a new speed to the hood.
NOTE: IIf there are multiple AMPERLINKS within the
same environment, it is possible to assign a unique
transmission code for each device:
- Press the P1 button for 10 seconds until you hear
the 2nd beep
- Repeat the procedure from STEP 1.
MAINTENANCE
WARNING:
- Do not use steam cleaners.
- Before proceeding with cleaning operations, make
sure that the appliance is turned off and that there is no
humidity or condensation, which can create dangerous
situations for the user.
- Do not use solvents or other detergents directly on
the external surfaces of the appliance, but use a cloth of
fabric, slightly moistened with the detergent substance
you want to use.
- 22 -