Refsta AMPERLINK Manual De Utilización página 21

ENGLISH
OVERVIEW
These warnings have been drawn up for your and
other's safety.
Therefore, please read this booklet carefully in all
its parts before using the appliance or carrying out
cleaning operations on it.
The Manufacturer declines all responsibility for any
damage that the appliance could, directly or indirectly,
cause to people, things, and pets resulting from failure
to comply with the safety warnings indicated in this
booklet.
It is essential to keep together this instruction booklet
with the equipment for any future consultation.
If the appliance were to be sold or transferred to
another person, make sure to provide as well the
booklet so that the new user will be aware of the
operation of the hood and the related warnings.
Require original spare parts
SAFETY PRECAUTION
BEFORE CONNECTING THE MODEL TO THE
ELECTRICITY NETWORK:
Check the data plate (located at the bottom of
the appliance) to make sure that the voltage and
power correspond to those of the network, and the
connection socket is suitable. If in doubt, consult a
qualified electrician.
This is the safety-related danger symbol, which
warns of potential risks for the user and others. The
danger symbol and the following terms will precede
all safety-related messages:
DANGER: Indicates a dangerous situation which, if
not avoided, will cause severe damage.
WARNING: Indicates a dangerous situation which,
if not avoided, could result in severe damage.
Do not install the device outdoors and do not expose
it to atmospheric agents (rain, wind, etc).
Disconnect the appliance from the power supply
before carrying out any installation work.
Installation or maintenance must be performed by a
specialized technician, following the Manufacturer's
instructions and in compliance with the local safety
regulations in force. Do not repair or replace any part
of the appliance unless specifically requested in the
user manual.
Grounding of the appliance is mandatory.
The power cable must be long enough to allow
the connection of the appliance, embedded in the
cabinet, to the mains. The power cable/connection
to the hob must not be longer than 200cm, to allow
correct operation.
The maximum distance between the appliance and
the hood to be controlled must not exceed 300cm (see
Fig. 5); otherwise, signal losses and, therefore, incorrect
operations may occur.
For the installation to comply with current safety
standards, an omnipolar switch with a minimum
distance of 3mm between the contacts is required.
Do not use multiple sockets or extension cables.
Do not pull the appliance power cable.
Once the installation is complete, the electrical
GB
components must no longer be accessible by the user.
Children must not play with the appliance.
Cleaning and maintenance by the user must not be
carried out by children without supervision.
The installation work must be carried out by competent
and qualified installers, as indicated in this booklet, and
respecting the regulations in force.
Do not modify the electrical, mechanical, and functional
structure of the equipment. Do not attempt to carry
out repairs or replacements yourself: interventions
carried out by non-competent and qualified people
can cause damage, even very serious, to things and
people not covered by the Manufacturer's warranty.
The appliance is intended for domestic use only for
the management of kitchen appliances. No other
methods are allowed. The Manufacturer declines
all responsibility for inappropriate use or incorrect
settings of the controls.
IEC 60730-1: 2013 + AMD1: 2015 Standards
Reference
CONNECTION TO THE ELECTRICITY NETWORK
WARNING: The electrical system to which the
appliance is connected must be compliant with and
earthed according to the safety regulations of the
country of use; it must also comply with European
regulations on radio interference suppression.
Disconnect the appliance from the power supply.
The installation must be carried out by qualified
personnel who are aware of the current safety and
installation standards.
The Manufacturer declines all responsibility for any
injury to people or animals and damage to property,
were it to derive from failure to comply with the
standards indicated in this section.
Check that the voltage indicated on the serial number
plate, at the bottom of the appliance, is the same as
the domestic electricity network.
1- Remove the cover (C) by unscrewing the screws
(Fig.7).
2 - Insert the power cables of the electrical network, in
the points named by "INPUT" according to the wiring
diagram below and the connection mode, whether it
is single-phase, two-phase or three-phase, always with
the Neutral present.
3 - Insert the power cables of the appliance (be it an
electric/induction hob, electric grill, oven or other
compatible appliance) in the points called "OUTPUT",
according to the electrical diagram shown below or
suggested in the reference manual of the appliance
itself. Always respecting the criteria listed above and
the presence of the Neutral connector.
4 - Fasten the cables with the cable glands present
and tighten the nuts to prevent accidental traction of
the conductors.
5 - Close the cover (C) and screw it with the screws
previously removed.
- 21 -