Tabla de contenido
Idiomas disponibles
Idiomas disponibles
gb
This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates
of our machines on the website:
www.grupostayer.com
1_MACHINE SPECIFIC SAFETY
WARNINGS
Keep hands and clothing away from the cartridge
ejection line and cartridge holder. Failure to do so
could result in staining.
Always work in well ventilated areas and wear
protection appropriate to the contents of the cartridge
you are using. Failure to do so may result in staining,
poisoning or injury.
Carefully read the instructions and specifications of
the cartridge you are using with the tool. Failure to do
so could result in poisoning or injury when applying the
product.
Stop the power tool immediately if the tool becomes
blocked.
Secure the workpiece. A workpiece clamped with
clamping devices, or in a vise, is held much more securely
than by hand.
Keep your workstation clean. Mixing different materials
is particularly dangerous. Powder mixtures can burn or
explode.
Wait until the power tool has stopped before putting
it down. The tool may become entangled and cause you
to lose control of the power tool.
BATTERIES USE AND CARE
Do not open the battery. Danger of shortcircuiting.
Protect the battery against heat, e. g., against continuous
intense sunlight, fire, water, and moisture. Danger of
explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery
against dangerous overload.
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The battery
can be damaged.
The battery is equipped with a temperature control
which allows charging only within a temperature range
of between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithiumion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithiumion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be
subject to overload. When the load is too high or the
allowable battery temperature range of 0–50 °C is
exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction ,
until the tool can be inserted. Insert the tool. Firmly tighten
the collar of the keyless chuck 2 by hand in rotation
direction . This automatically locks the drill chuck.
The locking is released again to remove the tool when the
collar is turned in the opposite direction.
2_FUNCTIONAL DESCRIPTION
PLACING OR FIXING THE TOOL
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
PRODUCT FEATURES
The numbering of the product features refers to the
illustration of the machine on the graphics page.
Screwdriver bit
1
Support
2
Bracket gasket.
3
Push rod.
4
Push knob.
5
Switch.
6
Safety button
7
Speed regulator
8
Battery
9
Battery disconnect button
ASSEMBLY
Battery charging
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time.
The lithium ion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The
battery can be damaged.
-
10
-
Tabla de contenido
