Idiomas disponibles
Idiomas disponibles
Thank you for buying a HIGHSIDER product. Because of our passion for motorcycles all our products are designed to meet your needs as a motorcyclist. We wish you always a safe and pleasant ride with your new HIGHSIDER product
from Paaschburg & Wunderlich GmbH.
Only when professionally installed is the statutory warranty and driving safety fulfilled. Pay attention to the information in the operating instructions of the vehicle or specifications of the vehicle manufacturer.
Failure to follow the assembly instructions can damage your vehicle and void the warranty. This is necessary to not affect the riding safety. No liability is accepted for consequential damage.
The unauthorized reworking and / or modification of the product can lead to the failure of the function and is not permitted. No entry in the vehicle documents or the carrying of any documents is necessary.
Please keep these instructions for later use!
Scope of delivery:
1 Pcs. HIGHSIDER headlight protector
Installation of the headlight protector:
1. Before fitting, make sure your vehicle is secure and disconnect the battery.
2.
ATTENTION:
All screws should be tightened only slightly at first. Only after all screws have been installed and the headlight has been adjusted correctly, tighten all screws.
3. Mount the headlight protector in a suitable place on the vehicle. The mounting position of the headlight protector is not specified Fig.1 or 2.
4. Mount the headlamp on the headlamp guard Fig. 3, 4, 5.
5. ATTENTION: Set the correct alignment of the light modules according to the applicable regulations! Failure to do so may result in loss of the operating permit.
6. ATTENTION: Secure all screws with threadlocker, e.g. #860-635.
7. ATTENTION: Due to the stress that can occur during operation, screw connections may loosen over time! It is therefore necessary to check the tightness of all parts before each ride!
Before each ride: It is the duty and responsibility of the rider to regularly check and maintain the safety-related vehicle parts. Before starting your journey, check the correct adjustment and function of the HIGHSIDER products and the tightness of all screwed connections.
Warranty: Take the time to do a 100% professional job of installing the HIGHSIDER products. Take into account all our installation and safety instructions.
A faulty, improper installation or handling of the product will void the warranty.
Maintenance/Care: Do not use aggressive detergents to care for the HIGHSIDER products. The HIGHSIDER products can be perfectly cleaned with a simple, lukewarm detergent solution. Contact with brake fluid, brake cleaner, fuel, etc. should be avoided. Immediately pick
up any unintentionally applied impurities with a soft cloth and clean the surface with detergent solution
Enviromental Information: This product may not be disposed in the normal household rubbish at the end of its lifetime. The disposal can be done through the Paaschburg u. Wunderlich customer service or a local return and waste collection institution.
HIGHSIDER Tips & Tricks on
https://www.youtube.com/c/HIGHSIDERTippsTricks
Exclusion of liability and warranty regulation:
In the event of improper handling, installation or use of the device, warranty and guarantee claims may expire. Due to the non-verifiability of the correct application, Paaschburg und Wunderlich GmbH assumes no liability for direct or indirect damage or consequential damage resulting from the operation of the device.
This does not apply if the damage is based on intent or gross negligence on the part of Paaschburg & Wunderlich GmbH, or if the damage consists in injury to life, limb or health, or Paaschburg & Wunderlich GmbH has culpably violated an essential contractual obligation (cardinal obligation).
Paaschburg & Wunderlich GmbH, Am Alten Lokschuppen 10a, D-21509 Glinde (GER),
Tel.: +49 (0) 40 248 277-0; E-Mail:
220-022A_Rev00_2021-09
Please read this manual carefully prior to installation
Find useful additional accessories like stem extensions, resistors, electronic relays, adapter cables and other equipment in our Webshop!
:
and safety instructions
Mounting
HIGHSIDER headlight protector for all FT13, SATELLITE, COMET
You can find more
products at:
www.highsider-germany.de
A = Ø 34 mm
B = 132 mm
A
B
www.highsider-germany.de
All rights reserved. Changes and errors are excepted.
Seite 3 von 5
