WETRA-XT Asist AE5PK110 Instrucciones De Uso página 38

an agreement between the manufacturer and the
customer.
Construction
Handle assembly
Hold the handle / 9 / in position in the appropriate
place (see pictures on the folding side) Insert the wing
screw with the handle and the housing and tighten it.
Vise assembly
Fasten the vice / 16 / using the supplied 4 hexagon
socket head cap screws in the corresponding holes
on the back of the saw plate. To do this, use a 5 mm
Allen key.
Installation of cutting angle adjustment on the saw
board
Fully loosen the cutting angle adjustment screw.
Insert the screw from below through the recess in the
bracket on the saw blade and tighten again to adjust
the cutting angle.
tilting side.
Secure the swivel arm with the second hole on the
saw plate with a long thumbscrew.
Assembly of a band saw on a rotating arm
To use the device with a saw blade, follow these
steps:
Fasten the swivel arm to the corresponding ho-
les in the housing of the device using the 3 long
thumbscrews provided.
NOTICE
If the swivel arm has too much play, occasionally
tighten the nut and wrench.
WARNING!
The band saw may only be used without a saw
blade if the user has taken a safe and calm stance.
In addition, the workpiece must be secured against
slipping on
work desk.
Always make sure that the power cord does not come
close to the saw blade. To use the appliance with a
saw blade, secure the mains cable with the cable
holder. For any other use, it must be such that the
cable can never reach the saw area, work area or
other dangerous area.
Make settings
Handle adjustment
To adjust the handle, loosen the thumbscrew on the
handle. Turn the handle to the desired position.
Tighten the thumbscrew again.
Using a vice
Turn the handle on the vice clockwise to clamp the
workpiece. Turn the handle on the vice countercloc-
kwise to release the workpiece.
NOTICE
You can also tilt the 15q quick adjustment up to
adjust the vice more quickly. Quickly lower the 15q
adjustment again to secure the vice. Then make the
exact adjustment of the vice handle.
Transport insurance
To turn the band saw upwards, pull out the locking
pin. Turn the band saw down and push the lock
pin inside. Now you can transport the band saw with
the saw blade more easily.
Cutting angle setting (miter angle)
Allow the cutting angle to be adjusted by turning it
counterclockwise. Set the desired cutting angle using
the steps shown. Tighten the cut angle adjustment
clockwise.
Workpiece stop setting
During normal operation, the workpiece stop must
be fixed in the lowest position. If the workpiece stop
interferes during cutting, you can loosen the workpie-
ce stop screw. To do this, use the supplied Allen key,
small. This will allow you to move the stop
workpiece up. Then secure the workpiece stop again
with the workpiece stop screw.
Saw blade replacement
Wear safety gloves to prevent
to injury.
Release the saw blade clamping lever countercloc-
kwise.
Remove both locking screws with a small Allen key.
Remove both protective covers.
Carefully remove the saw blade. Start on the guide
rollers.
Remove any sawdust present with a brush or com-
pressed air. Insert the saw blade with the saw teeth at
the top into the guide rollers. Make sure that the guide
rollers fully grip the saw blade.
NOTICE
Make sure that the direction arrow on the saw blade
(if available) matches the direction arrow on the rub-
ber wheels. Place the saw blade around both rubber
wheels. Tighten the saw blade tension lever clockwise
again. Refit both guards.
WARNING!
Only operate the device with the protective covers
fitted! Perform a test run by briefly turning the instru-
ment on and off several times to determine
whether the saw blade is seated correctly.
Keep your body out of the cutting area during the test
run!
Commissioning
Switching on Press and hold the power key 3.
Switching off Release switch 3.
Set the light switch on to position I.
The work light is on.
Set the light switch off to position 0.
The work light goes out.
Speed setting Set the speed dial to a position betwe-
en 1 and 6.
Work instructions
Secure the workpiece against slipping, eg with the
saw plate vice.
Use the saw's own weight when cutting.
Do not apply additional pressure.
Before carefully bringing the saw into contact with the
workpiece,
wait until the saw reaches full speed.
38