Technical Data - Healthcraft PLUS-CS Serie Instrucciones

OVERVIEW
Thank you for choosing the PLUS Corner Shelf. Please read and
understand the instructions in this manual; keep manual for future
reference. It is your responsibility to see that your PLUS Corner Shelf is
properly assembled, installed, and cared for. Failure to follow instructions in
this manual could result in serious injury or death. If you are not equipped
to undertake the outlined work, we would recommend that you have your
PLUS Corner Shelf installed by a qualified contractor.
The PLUS Corner Shelf is a combination grab bar and corner shelf,
designed to disguise safety in a bathroom accessory. The PLUS Corner
Shelf is intended for moderate vertical and horizontal load bearing to
provide sitting and standing support for people with reduced mobility. The
PLUS Corner Shelf is installed with appropriate fasteners to a structural
wall. The tray (which holds bottles) is NOT intended to be a support
product. The maximum user weight for this product is 500lbs / 227kgs.
Note: Product is not intended to support full body weight. The PLUS Corner
Shelf is not to be used in any other way than described above.
LIMITED LIFETIME WARRANTY
Products are covered by a limited lifetime warranty against defects in
materials and workmanship for the original purchaser. Warranty excludes
products that have been damaged through misuse, accidental damage,
alteration, normal wear and tear, wood material and stain, or the use of
corrosive or abrasive cleaning products.
Buyer hereby indemnifies, agrees to hold harmless and defend HealthCraft
Products Inc. from and against any and all liabilities, claims, (founded and
unfounded), losses, damages, costs and expenses (including without
limitation consequential damages and reasonable professional fees)
resulting from buyers specification, application, or improper use of goods
described hereon; buyers omission or neglect. HealthCraft Products Inc.
does not assume any liability for damage resulting from services performed
by others or faulty installation, misuse or misapplication of goods sold by
HealthCraft Products Inc. HealthCraft Products Inc. shall not be liable for
prospective profits or special, indirect, or consequential damages, or for the
cost of any corrective work done without HealthCraft Products Inc. prior
approval. HealthCraft Products Inc. total liability hereunder shall in no
event exceed the purchase price of the goods specified hereon.
Specifications subject to change without notice.
HealthCraft Products Inc.
2790 Fenton Road
Ottawa, Canada
K1T 3T7
6
English
Gate 88
Kanalgatan 45B
Skellefteå, Sweden
EC REP
93123
DELIVERY CONTENTS / CORNER SHELF
1. Rail (Corner Shelf)
2. #10 x 1.75" Wood Screw, S/S (x6)
3. Plastic Plug (x2)
INSTALLATION WARNINGS
1. Rail must be installed to walls that are structurally sound. If desired
installation location does not have adequate structure, add wood blocking.
2. CAUTION - Do not install if structure behind walls is unknown.
3. CAUTION - Do not install if there is no structure for one side. Do not
install if there is no structure behind drywall.
4. To reinforce hollow walls, we recommend Easy-Mount Anchors (each
sold separately). Weight capacity 300lbs.
5. CAUTION - Do not install into metal studs.
6. CAUTION - Do not install in fiberglass / acrylic shower enclosures with
insufficient stiffness and strength.
SUGGESTED CORNER SHELF LOCATIONS
To determine the optimal mounting location, we recomment holding the rail
in place and walking through the motions of a transfer (sitting, standing,
reaching, etc.). Recommended rail height 36-48" / 91-122cm.

TECHNICAL DATA

See Figure D.
INSTALLATION
1. Hold the corner shelf handle against the wall and adjust with level.
Using the flanges as a locating guide, mark the screw hole locations.
2. Drill pilot holes for fasteners.
3. Fasten the corner shelf handle to the wall using appropriate fasteners
and waterproofing. Inspect hardware regularly, and tighten if required.
4. Rotate the flange cover to gain access to other mounting hole (beside
top hole), and repeat steps 1-3.
5. Rotate the flange cover to gain access to other mounting hole (bottom
hole), and repeat steps 1-3.
6. Install plastic caps to cover the hole in the flange cover.
PRODUCT USAGE
CAUTION - Rail and bathtub are slippery when wet.
FIGURE A.
FIGURE B.
FIGURE C.
FIGURE E.
FIGURE F.