Tabla de contenido
Idiomas disponibles
Idiomas disponibles
WArNING:
OPErATING INSTrUCTIONS BEFOrE USING THIS EQUIPMENT. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious personal injury.
EXTENSION COrDS
Grounded tools require a three wire extension cord
either a two or three wire extension cord. As the distance from the power supply outlet increases, you must use a
heavier gauge extension cord. using extension cords with inadequately sized wire causes a serious drop in voltage,
resulting in loss of power and possible tool damage. Refer to the table shown below to determine the required
minimum wire size.
The smaller the gauge number of the wire, the greater the capacity of the cord. for example: a 14-gauge cord can
carry a higher current than a 16-gauge cord. When using more than one extension cord to make up the total length,
be sure each cord contains at least the minimum wire size required. If you are using one extension cord for more
than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure it is marked with the suffix "W-A" ("W" in Canada) to
indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged
extension cord or have it repaired by a qualified person before using it.
• Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
Recommended Minimum Wire Gauge for Extension Cords (120 Volt)
Nameplate
Extension Cord Length
Amperes
25 Feet
(At Full Load)
0–2.0
18
2.1–3.4
18
3.5–5.0
18
5.1–7.0
18
7.1–12.0
18
12.1–16.0
14
16.1–20.0
12
SPECIFIC SAFETY rULES FOr COrDLESS SCrEWDrIVErS
WArNING:
(GAINED FrOM rEPEATED USE) rEPLACE STrICT ADHErENCE TO PrODUCT SAFETY
rULES. If you use this tool unsafe or incorrectly, you can suffer serious personal injury!
WArNING:
operation where cutting tools may contact hidden wiring or its own cord. Contact with a
"live" wire will make exposed metal parts of the tool "live" and shock the operator!
•
Do not leave the tool running
•
Be Aware that this tool is always in an operating condition,
have to be plugged into an electric outlet.
•
When operating the tool from an elevated positio
beneath you.
•
Always hold the tool firmly in your hands before switching the tool "ON"
reaction to the torque of the motor as it accelerates to full speed may cause the tool to twist.
•
Wear eye and hearing protection.
otherwise specified, everyday glasses provide only limited impact resistance, they are not safety glasses.
use only certified safety equipment; eye protection equipment should comply with ANSI z87.1 standards.
Protective hearing equipment should comply with ANSI s3.19 standards.
All manuals and user guides at all-guides.com
rEAD AND UNDErSTAND ALL WArNINGS, CAUTIONS AND
SAVE THESE INSTRUCTIONS
50 Feet
18
18
18
16
14
12
10
DO NOT LET COMFOrT Or FAMILIArITY WITH THE PrODUCT
Hold the tool by insulated gripping surfaces when performing an
.
Operate the tool only when hand-held.
75 Feet
100 Feet
18
18
18
16
16
14
14
12
12
10
10
10
8
8
n
,
Always use safety glasses with side shields. unless
.
Double insulated tools can use
150 Feet
200 Feet
16
16
14
14
12
12
12
10
8
8
8
6
6
6
because it does not
be aware of people or things
.
The
5
Tabla de contenido
