RAUMER 109 Manual De Información Del Producto página 3

Ocultar thumbs Ver también para 109:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 7
ENGLISH
General information about RAUMER products comply with
Directive 89/686/CEE
This general information explains how to use correctly the anchors.
The general information must be associated to the technical data sheet and the inspection sheet.
Read both documents to have a complete information and ascertain to understand well all the
informations, before to use the product.
Only the techniques shown without symbol of death are authorized.
Take Vision of the updates and of all the addictional informations on the site
www.raumerclimbing.com
In case of doubt or difficulty to understand the informations, don't risk, but contact Raumer Srl –
Via Lago di Lesina 15B – 36015 Schio (VI).
Anellox Ø 8 – Art. 189
Anellox Ø 10 – Art. 190
Anellox Ø 12 – Art. 583
Anellox Sghembo Ø 8 – Art. 593
Anellox Sghembo Ø 10 – Art. 571
Anellox Sghembo Ø 12 – Art. 582
Reference Standard:
Anchor Device type A - EN 795: 2012
Rock Anchor - EN 959: 2007
UIAA 123-2
Material: Stainless Steel AISI 316 L
USE AND APPLICATION
Personal protective equipment (PPE) class III for protection against falls from a height, that is
used to connect devices to each other; It is intended for rock climbing, caving, canyoning and
mountaineering.
Anellox Art. 189, 190 and art. 583 and Anellox Sghembo Art. 593, 571 and art. 582 are type A
anchors devices, have been tested according to EN 795:2012, for use by one person and they're
removable from the structure.
The Anellox or Anellox Sghembo are tested according to EN 959:2007 if couple with its relative
Hang Fix, and it's designed for use as rock anchors; rock anchors are defined as anchor devices
insert in a rock hole, held in place by resin (or expansion forces) and with an attachment point for
a connector.
The anchor device is tested according to UIAA 123-2 - rock anchors.
When the anchor device is used as part of a fall arrest system, the user must be equipped with
the necessary means to limit the maximum dynamic forces exerted on them during the arrest of
a fall with a maximum of 6 kN.
Warning: this anchor device must be used exclusively for protection against falls from a height
and not for lifting equipment.
Don't stress the product beyond its limits or in other different situations than that for which it is
intended.
Check that the product is compatible with the other materials you want to use: contact Raumer if
you are not sure of compatibility.
Attention: activities involving the use of this device are all dangerous and high-risk and may
also involve in fatal injuries. Make sure you fully understand the use of this product and work
out in how to use it, to familiarize yourself with it and learn to know its performances and
Art. 189 – 190 – 583 – 593 – 571 - 582
Art. 109:
M12 x 74 mm - weight 150 gr
Art. 114:
M12 x 100 mm – weight 170 gr
Art. 224:
M12 x 120 mm – weight 190 gr
Art. 156:
M10 x 66 mm – weight 119 gr
Art. 157:
M10 x 86 mm – weight 130 gr
Art. 215:
M10 x 86 mm – weight 132 gr
Art. 150:
M10 x 110 mm – weight 145 gr
Art. 122:
M 8 x 78 mm – weight 103 gr
Art. 149:
M 8 x 100 mm – weight 112 gr
Material:
Stainless Steel AISI 316 L
DYNAMIC STRENGHT TESTS
1)
Perpendicular and lower direction respect to the longitudinal axe of the device
2)
Perpendicular and upper direction respect to the longitudinal axe of the device
3)
Parallel direction respect to the longitudinal axe of the device
Peak of force during the fall, according to the point 1): KN 9,4
Peak of force during the fall, according to the point 2): KN 9,5
Peak of force during the fall, according to the point 3): KN 9,5
Maximum deflection of anchor device: 0 mm
Maximum deformation of anchor point: 0 mm
MARKING
Producer: Raumer Srl – identified with logo "Raumer"
Identification of the model – Art. n. (esempio: 190)
Pictogram indicating the need to
read the instructions before use:
Lot number: (es. 001)
Month and year of manufacture: (es. 0515 = maggio 2015)
Notification body that intervening for
examination CE and for annual checks: CE 2008 - DOLOMITICERT
Reference Standards:
EN 795:2012
EN 959:2007
Radial load bearing capacity: KN 25
Axial Load bearing capacity: KN 20
Si veda inoltre la tabella riportata nella allegata scheda tecnica relativa alla resistenza effettiva.
See the table on the attached data sheet, with the effective resistance.
Material: Stainless Steel INOX AISI 316 L
Device usable by only a single connected user: 1P
Markings should always be read for all the lifetime of the product and must not be removed.
It's recommended that the anchor device is marked with the date of the next or last inspection.
If the marking of the connector is no longer accessible after installation, it must be provided
some additional markings near the device.
Risks of use and responsibility
This product should only be used by competent persons and who have received adequate
training, having been subjected to visual inspection by a trained and competent person.
It's yours responsibility to know this product, learn to use it, learn the proper techniques and
the safety measures. You alone are solely fully all risks and responsibilities for any damage,
You are responsible to consider all the notices and updates regarding these products.
No liability will be recognized by the company Raumer Srl for damages, injuries or death caused
by: improper use (also due to support or unsuitable environment), stresses the product beyond
its limits, modification of the product, repairs made by unauthorized persons.
If you are not able to undertake this responsibility and take these risks, do not use these
products.
Your life depends on the continual efficiency of your equipment (we strongly recommend that the
equipment is for personal use) and its history (use, storage, controls, etc.)
If the product is not for personal use (for exemple is of associations), we strongly recommend
that the pre and post- use controls carried out by a competent person.
Check and make sure that all the anchors do not show signs of cracks or wear.
Before using the equipment consider as a possible rescue, in case of emergency, it can be
performed safely and efficiently.
Attention! Do not use the product if the user's physical conditions are not appropriate for work
prescribed. Do not use this product if you suffer from medical conditions such as vertigo,
labyrinthitis or other conditions which may compromise the safety of the equipment in normal
use or emergency.
CHECKS AND INSPECTIONS
Before each use
Before each use, make sure that the product is:
in very good condition and working properly;
suitable for the use you intend to do: they are authorized only the techniques not
crossed out; any other use is forbidden: beware of death! The examples shown in
the attached form are just some of the wrong applications: there are many other
more that is impossible to list;
free of cracks, deformations and corrosions ;
Carefully check the state and the type of support in that you want to fix the product; if the rock is
cracked, etc. ... avoid it. If you have the minimum doubt about the safety and the effectiveness of
the product, replace it immediately.
During each use
Regularly check the state of the product and make sure you have correctly connected all devices
among themselves . Check visually the goodness of the anchor.
The resistance of natural/not natural anchors, in the rock, can't be guaranteed in advance, so It's
necessary a critical judgment by the user, to guarantee an appropriate protection.
Periodical inspections
It's not enough to check the material before and during each use, but periodical checks must be
done by a technician authorized by the manufacturer at least every 12 months; all the checks pre
and post use must be done by a competent person (the frequency depends from the intensity
and type of use).
When carrying out the checks is necessary to report the results of an inspection sheet; this
should allow you to record a lot of data; The inspection sheet should always be attached to the
general
information
of
the
product
and
is
www.raumerclimbing.com.
The product should be used only by one person, so that you know well the whole story of the
product.
Caution: You must make regular periodic inspections! The safety of users depends on the
continued efficiency and durability of the equipment.
We recommend to hold and fill the inspection sheet for each component, system and sub-system.
You can also download it from the site www.raumerclimbing.com
COMPATIBILITY
This product can be used in conjunction with personal protective equipment, in compliance with
Directive 89/686 / EEC and in accordance with the instructions of use (if devices are compatible
there is a good functional interaction). An anchor must be compatible to the device to which it is
connected; if the connection is inconsistent, you can compromise the security features of the
system (release or break ...).
Compatible devices are, for example, manufactured and certified harnesses according to EN
12277, dynamic ropes certified according to EN 892, connectors in accordance with EN 362 or
12275, etc ...
also
downloadable
from
the
site
11 - 2015
Tabla de contenido
loading

Este manual también es adecuado para:

14224156157215150 ... Mostrar todo

Tabla de contenido