TUBESCA-COMABI Totem 2 Cross 2 180 Instrucciones De Montaje página 12

TOTEM 2 CROSS 2
 The instruction manual should be available at the site where the mobile tower is being used.
 The mobile access and working tower should only be used in accordance with this manual, and should not be modified in
any way.
 Mobile access and working towers should only be used in accordance with national regulations.
 The mobile tower should be used intentionally as a means of accessing the working area.
 All components, tools and other necessary equipment to assemble the mobile tower should be available at the site.
 Before assembling the mobile access and working tower, the chosen site should be checked to identify and prevent hazards
during its assembly, modification and dismantling, including, and without limitation:
Ground conditions;
o
The level of the slope;
o
Obstacles (on the ground or in the air);
o
Weather conditions;
o
Hazardous electrical phenomena.
o
 Assemble the mobile access and working tower according to the instructions in this manual for assembly and use.
 Ensure that all necessary split pins and bolts are firmly in place.
 TOTEM 2 should only be erected and dismantled by personnel trained in assembling and using the mobile tower.
 User training courses are not a substitute for instruction manuals, but can complement them.
 Only original TUBESCA-COMABI components, as specified in this manual, should be used.
 Damaged or faulty components should not be used.
 For assembling each element, refer to the previous diagrams in sections §1-4.
 PPE (Personal Protective Equipment) must be worn for assembly and dismantling.
 Stabilisers must always be positioned at an angle; refer to the diagrams and the table in the following sections §2-2-5 (Rules
for assembling stabilisers).
 Two-person assembly is required.
 Different levels can be accessed from inside the mobile tower via the trap doors
 Hauling up items to raise the height of the product can be done from the guard rail side once this has been installed.
 Hauling up tools or other items whilst the product is in use can be done through platform access trap doors.
 This product should only be used in accordance with the instruction manual.
 Mobile access and working towers designed in accordance with EN 1004-1 are not anchor points for fall arrest systems.
 Working on a platform is only allowed if there is a complete guard rail consisting of handrails, intermediate rails and
toeboards.
 After assembly or modification, the following basic information should be displayed on the mobile access and working
tower, and it should be clearly visible from the ground (on a label, for example):
The name and contact details of the person in charge;
o
Whether the mobile access and working tower is ready for use or not;
o
The load category and the uniformly distributed load value for the mobile access and working tower;
o
Whether the mobile access and working tower is solely intended for interior use only;
o
The assembly date.
o
Instructions drawn up following a risk assessment of TOTEM 2 CROSS 2.
These instructions refer to the corresponding evaluation documentation according to EN 1004-1
 Die Betriebsanleitung muss am Einsatzort der fahrbaren Zugangs- und Arbeitsbühne verfügbar sein.
 Diese fahrbare Zugangs- und Arbeitsbühne darf nur gemäß dieser Anleitung ohne jegliche Änderung eingesetzt werden.
 Fahrbare Zugangs- und Arbeitsbühnen müssen grundsätzlich in Übereinstimmung mit den national geltenden
Vorschriften eingesetzt werden.
 Das Produkt dient dem Zweck, den Zugang zum Arbeitsbereich zu ermöglichen.
 Die Komponenten, Werkzeuge und sonstigen Ausrüstungen zur Montage der fahrbaren Zugangs- und Arbeitsbühne
müssen am Einsatzort zur Verfügung stehen.
 Vor der Montage der fahrbaren Zugangs- und Arbeitsbühne ist der Einsatzort zu prüfen, um mögliche Gefahren beim Auf-
, Um- und Abbauen zu erkennen und zu verhindern, darunter:
Grundbeschaffenheit;
o
Gefälle;
o
Hindernisse (am Grund und in der Höhe);
o
Wetterbedingungen;
o
Elektrische Gefahren.
o
12