Tabla de contenido
Idiomas disponibles
Idiomas disponibles
(UE) 2016/425 Regulation of the European Parliament and the Council of the European Union
and in accordance with the instructions of use (if devices are compatible there is a good
functional interaction). An anchor must be compatible to the device to which it is connected; if
the connection is inconsistent, you can compromise the security features of the system (release
or break ...).
Compatible devices are, for example, manufactured and certified harnesses according to EN
12277, dynamic ropes certified according to EN 892, connectors in accordance with EN 362 or
12275, etc ...
Warning: Please avoid the use of these anchors with others made of different materials. For
example, do not use Anellox made of stainless steel and galvanized steel anchors, because also in
a modest hostile environment there will be obtained effects of galvanic corrosion.
Contact Raumer if you are not sure of the compatibility of your device.
OPERATING MODE
See informational sheets about:
Installation
Make sure about the hardness, the nature and compactness of the rock on which you'll insert
the anchor.
Clean the rock and remove any friable part; create a pitch to put the Hang Fix and the Anellox.
The area for fixing the anchor must be absolutely massive. In addition to all the other
evaluations, a good method is to beat vigorously on the chosen area with a hammer. The "sing"
of the rock must be dry and clear, and not as an isolated and "march" plaque.
You perform the hole in the rock with an appropriate electropneumatic hammer-drill, taking care
to make it perpendicular to the drilling plane. The depth of the hole should be at least 5mm
longer than the total length of the Fix. Attention to the diameter of the drill bit: must be exactly
as the diameter of the anchor.
Clean the hole from the powder, blowing inside it with the help of a little tube.
At this point it is necessary to proceed to fix the Hang Fix. Insert the Hang Fix (with the nut) into
the hole. With the hammer, tap on the head of the fix, introducing it into the hole, leaving a few
mm out of the rock (a dimension that corresponds to the thickness of the nut + about another 5
mm). Unscrew the nut and remove it, then insert the Anellox. Screw the nut onto the head of the
Hang Fix. Using a hexagonal wrench, tighten the nut with the correct tightening torque indicated
in the data sheet.
Attention!!!
•
When using an Anellox, always make sure the nail is made of the same material
and that the diameter is compatible.
•
These devices are resistant to corrosion according with standards (excellent
resistance to corrosion in the interior, but not excellent environment or
surrounding area of the seaside - see general information/lifetime ) .
•
The installation must be tested in an appropriate manner, for example by
calculation or test.
•
The installer must be a responsible person or organization, who has received an
appropriate training.
•
The load-bearing of the anchor cannot be guaranteed if the rock in which it is
installed is less strong or not very homogeneous, not consolidated or with micro-
cracks. In these cases we recommend using the anchor with a HANG FIX as long as
possible or prefer a different type of anchoring system, or choose a different area
in which to install it.
Resistence
Our products comply with the requirements of EN 795: 2012/A and EN 959:2018 – see attached
technical data sheet.
They are also comply with the requirements of UIAA 123
Please note that the company Raumer disclaims any responsibility in case of improper
installation and/or use in inappropriate rocks or inappropriate environments or inappropriate
dowels.
Precautions for use
Attention: after a fall or a major impact, check:
•
rock around the anchor: there must be no cracks;
•
anchor: observe it visually and check that there are no cracks, deformation, and
•
verify that the anchor is not rotated or moved;
Anellox – Anellox Sghembo
If you're in doubt replace it.
Use only if the external temperature is between -40 ° and + 50 ° C.
For safety purposes, it's essential to systems of arrest fall from a heigh, that the anchor point is
always placed, if possible, above the user; you use a complete safety belt; fixing is performed so
as to minimize potential falls and their height.
The position is essential for safely blocking a fall: carefully verify what will be the height of the
fall, length of rope and "pendulum" effect to avoid all possible obstacles (es. The ground, rubbing
against the rocks, etc.). Get used to always double systems, during your activities, for extra
security.
Always make sure that connectors inserted in their anchorage are free to move and position in
the right direction of load application.
COMPLEMENTARY STANDARDS INFORMATIONS
•
provide for a rescue plan and define the means to act quickly in case of difficulties
(It means to be trained to apply the appropriate rescue techniques).
•
allow a sufficient height under the user so, in case of fall, do not collide with
obstacles (remember that also the length of the carabiner can affect on the height
of the fall).
•
check to use the product with respect to government regulations and the safety
regulations in force.
•
respect all the instructions of use given in the general informations of each device
used or associated with this product.
•
attention: you need health fitness for the activities at height.
•
to the user of these devices must be provided all the instructions of use; the
retailers must deliver the device with these instructions, in the language of the
country of use, when It's sold out of the first country of destination.
It's a user responsibility to record and store with these instructions, the information provided in
the inspection sheet.
GENERAL INFORMATIONS
Life time
The potential life time of the Raumer's products is undefined (it is advisable to replace them
anyway after 10 years).
It is known that equipment may degrade progressively when it is used, so the actual life time of
the products can not be quantified precisely, but occurs when the product becomes obsolete in
the system or when it meets one of elimination.
The lifetime is also reduced considerably by the conditions and intensity of use: heavy use,
contact with chemicals substances, use near sea water or splashing water, high temperatures,
abrasions or cuts, damage to parts/components of the product, chemical environments, mud,
sand, snow, ice, competence of the user, violent shocks , storage, are some of the factors that
accelerating product wear.
Warning: the duration may be limited to only one use in specific conditions (contact with acids,
dangerous chemicals products, if the product suffers sharp falls or tensions, etc ... this list is not
exhaustive). In a marine environment or other potentially corrosive environments, it would be
better to use materials with high corrosion resistance , of class 1 , like titanium; we invites the
installer to monitor and inspect the anchors at regular intervals to check their status.
Attention: anchors installed in marine areas, on rocks containing ferrous inclusions or other
minerals of not certain nature, in some cases may suffer violent corrosive attacks that can
compromise its use even in very short time!
Attention: the life of the anchorage is considerably limited in the case of installation in an
environment with obvious Stress Corrosion Cracking SCC.
Elimination
Do not use the product:
•
after a violent fall, since no visible deformations could be considerably impaired
resistance;
•
if the result of the check is not satisfactory;
•
when you do not know the entire history of its use and when it becomes obsolete
and you have the slightest doubt about its reliability;
•
general wear of the plate and/or significant reduction of the section in
correspondence with the carabiner;
•
if there're cracks, wear or defects;
•
when corrosion severely alters the surface condition.
Destroy retired equipment to prevent further use.
Product obsolescence
The product may be judged obsolete and thus retired from service, when they occur, for
example, incompatibility with other equipment, changes in applicable standards, etc ...
Chemical products
All chemicals, solvents or corrosive substances can be very dangerous for these items. If there's a
chance to come in contact with these substances contact directly Raumer indicating composition
and exact name of the product, so we can respond properly after studying the case.
Changes and repairs
Modifications and/or repairs not authorized by the company Raumer are prohibited because
they can reduce product performance. Repairs or modifications must be carried out inside the
department production of Raumer Srl and not outside.
Warranty
This product has a 3-year warranty, against every defects in manufacturing or material.
The guarantee excludes oxidation, normal wear and tear, modifications or alterations, incorrect
storage, damage due to accidents, incorrect storage, negligence and improper use.
Transport
It does not need any special precautions for transportation, however avoid contact with chemical
reagents or other corrosive substances and adequately protect from any pointed objects or
sharp.
Maintenance and storage
The user should not perform any special maintenance, but should be limited to the cleaning of
the product as explained below.
Cleaning: frequently rinse the product only with lukewarm fresh water (max 40°C). Leave it to dry
naturally away from direct heat. Do not put the product in contact with corrosive substances or
solvents; do not store at extreme temperatures;
Storage: after cleaning and drying, store the equipments in a dry, cool, dark place (avoid UV
rays), chemically neutral place (absolutely avoid saline environments), away from sharp edges,
heat, humidity, corrosive substances or other potentially harmful conditions.
Caution: Do not store when wet! Improper storage, as well as the aging of the product, may
damage it and impair its performance and safety.
Testing and conformity
This product is tested in accordance with the standard by the Notified Body n°2008 -
DOLOMITICERT S.C.A.R.L., Z.I. Villanova 7/A– 32013 Longarone (BL).
This product is also tested and complies UIAA 123 : Quality Label of the International Climbing
and Mountaineering Federation.
Attention: laboratory tests, the instructions for use and standards are not always able to
reproduce the practice, so the results obtained in real conditions of use in natural environments
may sometimes differ to a considerable degree. The best instructions can be had from
continuous use under the supervision of qualified and prepared instructors.
Tabla de contenido
