Conformity Declaration - NOLOGO RX2-XL Manual Del Usuario

► CODE'S MEMORIZATION
LEARNING OF A TRANSMITTER
1. Make sure the exit´s receivers are not in use and not in learning the green led (L1 and L2) are turned off.
2. Push and release the push-botton corresponding to the exit of the remote control, P1: OUT1 or P2: OUT2
3. The green led associated will lit on
4. Press the transmitter's button within 5 seconds. If the code has been learnt, the red led fl ashes fast for 2 seconds. If the red led fl ashes
slowly it means that the memory is full. If the red led doesn't fl ash it means that the transmitter is not compatible.In order to learn other
codes on the exit 1 repeat operation 1.
TRANSMITTER'S CANCELLATION (not fot EB rolling).
This function can cancel only one single remote control:
1. Press and keep pressed the buttons P1 and P2
2. Press the button of the remote control which code need to be cancelled
3. Led L1 and L3 fl ash briefl y to confi rm the cancellation of the code
4. Release all buttons
DEACTIVATION OR ACTIVATE OF ONE REMOTE CONTROL (for Eb rolling).
The deactivation of one single remote control is useful in case the automatic memorization is always activate (DIP5 ON) and it doesn't need to
be memorized when the signal will be received. This procedure is useful in case to invert the managing of the remote control, if It was activated
or deactivated, and if it was deactivated, it will be activated:
1. Press for 2 seconds and then release the buttons P1 and P2 on the control board
2. Press the button of the remote control. Se questo è in memoria il led relativo all'uscita inizierà a lampeggiare.
3. If the code is activated it will be deactivated and vice versa.
4. If the buttons P1 and P2 will be pressed for more than 5 seconds, the code will be cancelled from the memory of the receiver
► FUNCTIONS
FUNCTION STEP BY STEP
The receiver´s exit can be made also used for the operation step by step. To active or disactive the operation it is suffi cient to push the button
when only the relative exit is active (green led switched on, L1: OUT1 and L2: OUT2). If the exit was in normal, the operation step by step will be
operating, while if the following operation was already active, the exit will return to the normal function.
FUNCTION STEP-BY-STEP WITH TIMING.
The output works as the step-by-step mode (DIP 6 OFF) with a self-deactivation after a planned time. To activate this function the receiver must
be in normal function (not step-by-step or step-by-step with timing) so when the output has been activated:
1. Press the button in the receiver corresponding to the output until the led start fl ashing and then release the button.
2. The green led fl ashes, L1: OUT1 or L2 OUT2.
3. Let the time goes for maximum 512 seconds for the timing and then press the button again.
4. To deactivate the function step-by-step with timing, it is suffi cient to press the button in the receiver to the corresponding output when the
output is activated.

Conformity declaration

NOLOGO S.r.l. declares that the following product RX2-XL is conformed to the following norms:
EN 301 489-3 (2000) Classe 1 EN 300 220-1 V2.1.1
EN 60 950 Mod. A1 (1993)-A2 (1993)-A3 (1995)-A4 (1997)
Me Ernestino Bandera, declares that the above mentioned product has been tested in a typical installation and fulfi l the essential requirements
of the laws:
99/5/CE
Permitted transmission frequency
433,92 Mhz BOX: ROSSO/RED/ROUGE/ROT
EU
868 Mhz BOX: BLU/BLUE/BLAU
2002/95/EC
All manuals and user guides at all-guides.com
100%
ITAL Y
Ernestino Bandera
Busto Arsizio, 01/06/2013
www.nologo.info
www.ebtechnology.it