Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Canopy assembly
•
Attach the zip at the end of the roof to the buggy frame (Figure 15a).
•
Do the zip running around the roof (Figure 15 b).
Use of the safety belts
•
The seat is equipped with 5-point safety belts.
•
The seat belt is released by pressing the red button in the middle of the crotch belt (figure 16).
•
To fasten the belts, insert all belt ends into the central buckle. The "click" sound indicates that
the belts have been correctly fastened (figure 17).
•
To adjust the length of the belts, use the buckles on the belts (figures 18, 19).
•
The position of the belts can be adjusted by inserting the buckle located in the backrest
behind the pushchair cover through the holes located at the appropriate heights. To do this,
the buckle must be turned in such a way so that it can slide through the longitudinal hole
(figures 20, 21, 22).
Use of the brakes
•
The pushchair is equipped with a hand brake. To lock the rear wheels, pull the lever located
on the right side near the handle of the pushchair (figure 23). A "click" sound means that the
handbrake has been applied.
•
To unlock, pull the small slider located on the right side, on the outside of the handle
(figure 24) and at the same time press the button located on the other side of the locking
mechanism, on the inside of the pushchair (figure 25). A "click" sound means that the hand
brake has been unlocked
NOTE! Note the bottom brake mechanism – locked brake is indicated by red colour inside the
window, while unlocked brake – by green.
Backrest tilt adjustment
•
The backrest is adjusted by a mechanism mounted on its outer side. To reduce the angle
between the seat and the backrest, turn the handle clockwise until the desired inclination of
the backrest is reached (figure 26).
•
To increase the angle between the seat and the backrest, pull the backrest adjustment
mechanism to obtain the desired inclination (figure 27).
Adjustment of the pushchair position
•
The pushchair can be set to 3 positions. They are adjusted by a mechanism located on its
outer side, above the canopy of the pushchair, on top of the frame (figure 28).
•
Position 1 is only to be used use for the carrycot function (figure 29).
•
Positions 2 and 3 are to be used for the seat function (figure 29).
WARNING! When changing the position of the pushchair, the child must not be present in the seat/
carrycot.
To position as a pushchair, put the backrest in position 1 or 2 and adjust the footrest by hooking
the straps on both sides into the respective hooks on the frame of the carrycot/seat (figure 29 a)
Height and handle direction adjustment
•
To set the desired height of the pushchair handle press the button in the middle of the
handle and adjust its length (figure 30).
•
The handle can be installed on either side of the pushchair. To change, use two buttons on
the sides of the handle which need to be pulled upwards at the same time (figure 31). Then put
the handle on the other side (figure 32).
Carrycot function
•
To retract the footrest, pull the belts on both sides of the seat and unhook the footrest lock
(figure 33). To use the footrest again follow the steps described above in the reverse order.
•
Tilt the backrest of the pushchair backwards as far as possible (figure 34) and then put it in
position 1 (figure 35).
•
There is a pocket on the underside of the seat where the stiffening inserts are placed (figure
36). When the carrycot is unfolded, stiffen the structure by sliding the 4 inserts into the
pockets on the sides of the carrycot (figure 37).
WARNING! All safety belts should be removed when using the carrycot function.
Removal of the safety belts
•
To remove the belts, turn the buckles at the ends of the belts, located behind the backrest
of the seat/carrycot and under the seat/carrycot, so that they can slide through the
longitudinal openings (figure 38).
•
Re-installing the belts can be done by sliding the belt buckles back through the appropriate
21
Tabla de contenido
