Before Starting The Equipment - HERKULES H-DS 150 Manual De Instrucciones Original

All manuals and user guides at all-guides.com
Load factor:
A load factor of S2 30 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (150 W)
for no longer than the time stipulated on the spe-
cifi cations label (30 minutes ON period). If you fail
to observe this time limit the motor will overheat.
During the OFF period the motor will cool again to
its starting temperature.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level ........................ 63 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 76 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Vibration emission value a
K uncertainty = 1.5 m/s
2
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anl_H_DS_150_SPK7.indb 15 Anl_H_DS_150_SPK7.indb 15
GB
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
2. Damage to hearing if no suitable ear protec-
3. Health damage caused by hand-arm vib-

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Pull the power plug before doing any mainte-
nance or assembly work on the equipment.
≤ 2.5 m/s
2
h
•
•
•
•
5.1 Assembling the spark defl ector / safety
•
•
5.2 Adjusting the spark refl ector
•
- 15 -
mask is used.
tion is used.
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a
work bench or similar.
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
It must be possible for the grinding wheel to
run freely.
Check that the voltage on the rating plate is
the same as your supply voltage before you
connect the machine to the power supply.
window (Fig. 3/4)
Fit the spark deflector (3) to the double wheel
grinder using the adjusting screw (10) (Fig. 3).
Fit the safety window (2) to the spark deflec-
tor (3) using the adjusting screw (11) (Fig. 4).
(Fig. 5 / Item 3)
Adjust the spark deflector (3) using the adjus-
ting screw (10) so that the distance between
the dry grinding wheel (5) and the spark de-
flector (3) is as small as possible and certain-
ly does not exceed 2 mm.
13.09.2016 08:00:37 13.09.2016 08:00:37