Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ENGLISH
Always use the appropriate type of attachment for the
u
workpiece material and type of cut.
Regularly check the condition of accessories. Replace
u
when necessary.
Mark the desired starting point.
u
Switch the tool on and slowly feed attachments into the
u
workpiece at the desired starting point.
Clamp a piece of plywood or soft wood to the back of the
u
workpiece and saw through the combination in order to
obtain a clear cut.
Do not force the cutting blade into the workpiece. Note
u
that cutting sheet metal will normally take more time than
sawing thicker wooden workpieces.
When cutting metal spread a thin film of oil along the cut-
u
ting line before cutting.
When sanding new layers of paint before applying another
u
layer, use extra fine grit.
On very uneven surfaces, or when removing layers of
u
paint, start with a coarse grit. On other surfaces, start with
a medium grit. In both cases, gradually change to a fine
grit for a smooth finish.
Consult your retailer for more information on available
u
accessories.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
10
(Original instructions)
Protecting the environment
Z
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com.
Technical data
Voltage
V
DC
No-load speed
min
-1
Oscillating angle
Degrees
Weight
kg
Charger
Input Voltage
V
AC
Output Voltage
V
DC
Current
A
Battery
BL1518
Voltage
V
18
DC
Capacity
Ah
1.5
Type
Li-Ion
Level of sound pressure according to EN62841:
Sound pressure (L
) 94.2 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L
) 105.2 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN62841:
Cutting wood (a
) 7.9 m/s
, uncertainty (K) 1.5 m/s
2
h, CW
Cutting metal (a
) 7.9 m/s
, uncertainty (K) 1.5 m/s
2
h, CM
Sanding (a
) 8.2 m/s
, uncertainty (K) 1.5 m/s
2
h
Sanding (a
) 8.2 m/s
, uncertainty (K) 1.5 m/s
2
h
Rigid scraper – Removal of glued carpet from a floor: (a
m/s
2
Rasp/grout removal blade- Scraping concrete: (a
Declaration of Conformity
The Supply of Machinery (Safety) Regulations 2008
Cordless Oscillating Tool - BDCOS18
BLACK+DECKER declares that these products described
under "technical data" are in compliance with:
EN62841-1:2015, EN62841-2-4:2014.
BDCOS18 H1
8000 - 18000
1.4 or 2.8
1.4
906349**
220 - 240
BL2018
BL4018
18
2.0
4.0
Li-Ion
Li-Ion
2
2
2
2
) 12.0 m/s
, uncertainty (K) 1.5
2
h
) 9.7 m/s
, uncertainty (K) 1.5 m/s
2
2
h
18
18
1
18
Tabla de contenido
