Intended Use; Before Starting The Equipment - EINHELL TE-TC 18/115 Li-Solo Manual De Instrucciones Original

acquainted with these operating instructions.
•
Portable tile cutting machine for medium-
sized tiles.
•
Cutting with the diamond cutting wheel.
•
Making jolly cuts with the tiltable work surface
(max. 45 degrees).
•
Wheel cooling with water.
•
Stop rail and angle stop.
•
Trough as cooling water container (to fill the
trough you must remove the water container
cover).
•
If the cutting wheel becomes jammed, switch
off the equipment and disconnect it from the
power supply; only then are you to remove the
workpiece

5. Intended use

The tile cutting machine is designed for the
standard cutting of small and medium-size tiles
(glazed tiles, ceramic tiles or similar) which can
be accommodated by the size of the machine. It
should never be used for cutting wood or metal.
The machine should be used exclusively for
its intended purpose. Any other use is deemed
to be a case of misuse. The user/operator and
not the manufacturer will be held liable for da-
mage and/or injuries of any kind that result from
such misuse. The machine is to be operated
only with suitable cutting-off wheels. Saw blades
should never be used. Compliance with the sa-
fety instructions, the assembly instructions, and
advice and instructions on operation contained
in the operating instructions also falls under the
terms of intended use. All persons who use and
service the equipment have to be acquainted
with this manual and must be informed about the
machine's potential hazards. In addition, strict
compliance with the accident prevention regula-
tions in force in your area, as well as all other ge-
neral rules of health and safety at work, is impera-
tive. The manufacturer's liability shall be deemed
void if the machine is modifi ed in any way and the
manufacturer shall therefore accept no liability for
any damages arising as a result of modifi cations.
Even when the equipment is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards may arise in
connection with the machine's construction and
design:
•
Contact with the diamond cutting wheel whe-
re it is not covered.
Anl_TE_TC_18_115_Li_SPK13.indb 19 Anl_TE_TC_18_115_Li_SPK13.indb 19
GB
•
Contact with the diamond cutting wheel while
it is turning.
•
Defective diamond tips flying off the cutting
wheel.
•
Kick-back of workpieces and parts of workpi-
eces due to improper handling.
•
Damage to hearing if ear-muffs are not used
as necessary.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

6. Before starting the equipment

Warning!
Always remove the battery pack before ma-
king adjustments to the equipment.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the diamond wheel to
run freely.
•
Before you actuate the ON/OFF switch, make
sure that the diamond wheel is correctly fit-
ted and that the machine's moving parts run
smoothly.
•
Before using the machine, check all of the
parts for damage and replace any parts that
are damaged. When replacing any parts or
accessories, always carefully follow the inst-
ructions in this manual.
•
For optimum performance and maximum sa-
fety, keep the machine clean at all times.
•
While the machine is running, check the wea-
ring parts and the fastenings of parts which
may have become loose and check that all
accessories are correctly fitted.
•
Notice! The tile cutting machine is desig-
ned for use with water.
•
Check that the water level is high enough to
cover the diamond part of the wheel each
time before you start a cutting operation and
keep checking it during cutting as well. Fill/
refill the cooling water directly into the trough.
- 19 -
12.08.2021 16:47:07 12.08.2021 16:47:07