Resumen de contenidos para Hiplok AIRLOK V1
- Página 1 US ER G UI DE 2 0 2 1 2018...
- Página 2 AIRLOK V 1 EXPANSION SLEEVE ( x4 ) SECURITY WASHER ( x4 ) M10 BOLT ( x4 ) BALL BEARING ( x4 ) METAL FRAME ( x1 ) OUTER COVER ( x1 ) COVER FIXING BOLTS ( x4 ) RUBBER FRAME HOLDER ( x1 ) LOCKING PIN ( x1 ) T O O L S R E Q U I R E D + R E C O M M E N D E D F O R F I T T I N G 1 X ELECTRIC DRILL...
- Página 3 I N S TA LAT I ON S T E P 1 Decide on the location for AIRLOK, taking into consideration the type and size of bike(s) it will secure and the type of wall it is being fixed to. Ensure there will be sufficient clear space around the AIRLOK and bicycle taking into account furniture, opening doors etc.
- Página 4 S T E P 2 Remove AIRLOK from box and slide metal frame from outer cover. Using the metal frame, mark the 4 holes with a pencil ensuring the unit is level. Drill four pilot holes using a 6mm or 8mm masonry drill approximately 20mm deep.
- Página 5 ST EP 3 55 - 60 mm 1 5mm Using a 15mm masonry drill bit (if using the supplied anchor bolts) drill each hole 55-60mm deep. Make sure these are clean and drilled level. Always vacuum out drilled holes before installing the anchor bolts.
- Página 6 Note: Once ball bearings are hammered into allen key holes, removal of the AIRLOK unit is not possible without damage to the wall or AIRLOK itself. Remember: If you’re unsure please call us, refer to our website www.hiplok.com or ask a professional for help.
- Página 7 S T E P 6 S T E P 7 Once the frame is secure on the wall, lift on the plastic Screw in the 4 allen bolts to body and slide into place. Ensure the plastic body is the secure the plastic body to the correct way up and it fully covers the frame on the sides.
- Página 8 L O C K I N G + L O A D I N G P R O C E D U R E When AIRLOK is not loaded with a bicycle, it is recommended to keep locking pin in locked position. To load / unload bicycle, unlock lock- ing pin with key (a) and pull down to lower position (b).
- Página 9 BIKE C OM PATIB I LI TY AIRLOK has been designed to work with the vast majority of bicycle frame shapes and sizes. Large box section frames, oversized tubes and unusual cross sectional shapes can be accommodated. However, we recommend checking the compatibility of your bike before installing your AIRLOK. See diagram below: If a rectangular of dimensions 150mm wide x 60mm length will fit under the top ( cross ) bar within the front triangle of your bike, then...
- Página 10 Ensure the bike is in a stable position and within lower area of rubber frame holder before releasing your grip of the bike and pushing locking pin into upper position. Take care when unlocking pin and removing bike also. For further support on compatibility and loading go to www.hiplok.com/airlok...
- Página 11 LIFETIME WARRANTY We stand by the quality of our locks and are proud to offer lifetime warranty on all Hiplok keyed chain and D locks. Register your lock now for piece of mind. Product must be registered at hiplok.com within 30 days of purchase to qualify for Lifetime Warranty.
- Página 12 Plus 8 Industries geeft geen andere uitdrukkelijke garanties of waarborgen dan de specifiek that might result from the use or handling of any Hiplok product by any legal or natural person. vermelde. Plus 8 Industries wijst alle verantwoordelijkheid voor derden af indien het gebruik of hanteren van een product van Hiplok door een juridisch of natuurlijk persoon negatieve gevolgen heeft.