SilverStone SUGO Serie Manual De Instrucciones
Ocultar thumbs
Ver también para SUGO Serie:
- Manual de instrucciones (63 páginas) ,
- Manual (44 páginas) ,
- Manual de usuario (36 páginas)
Enlaces rápidos
Manuales relacionados para SilverStone SUGO Serie
Resumen de contenidos para SilverStone SUGO Serie
- Página 1 SUGO SERIES SG08 September, 2011 G11214760...
-
Página 2: Product Overview
Product Overview The ultimate evolution of high performance Mini-ITX SG08 Specification Model SST-SG08B (Black) Expansion Slot Aluminum front panel, SECC body Material Front I/O Port USB 3.0 port x 2, Audio x 1, MIC x 1 Motherboard Mini-DTX, Mini-ITX Custom 600W with 80 PLUS Bronze Power Supply External Slim optical x 1... - Página 3 3.5” HDD CAGE 3.5” HDD x 1 2.5” HDD x 2 TOP COVER EXPANSION SLOT x 2 FAN BRACKET SLIM OPTICAL DRIVE (OPTION) USB 3.0 + SPK + MIC MINI-ATX (OPTION) POWER LED & HDD LED POWER BUTTON FAN FILTER PSU FILTER 18032 FAN x 1 USB 3.0 CONNECTOR...
- Página 4 Before you begin, please make sure that you: (1) have all components collected. (2) check that all components do not have compatibility problems with each other or with the case. (3) if possible, assemble the components outside the case first to make sure they are working. (4) keep the motherboard manual ready for reference during installation.
- Página 5 Unscrew screws holding the Выкрутите крепежные винты optical drive bracket to remove it. кронштейна привода оптических дисков, чтобы извлечь его. Lösen Sie die Schrauben der 광드라이브 브라켓을 고정하고 있는 Halterung des optischen Laufwerks; 나사를 풀어 브라켓을 제거합니다. entfernen Sie sie. Dévisser les vis maintenant le 光学ドライブブラケットを固定し...
- Página 6 Unscrew screws holding the Выкрутите крепежные винты кронштейна hard drive bracket to remove it. жесткого диска, чтобы извлечь его. Lösen Sie die Schrauben der 하드드라이브 브라켓을 고정하고 있는 Festplattenhalterung; entfernen 나사를 풀어 브라켓을 제거합니다. Sie sie. Dévisser les vis maintenant le ハードドライブブラケットを固定し...
- Página 7 Connect ATX 24pin, EPS 8pin/ATX 4pin connectors, front panel connectors, and front I/O connectors to your motherboard. Verbinden Sie die 24-poligen ATX-, 8-poligen EPS- / 4-poligen ATX-, die Frontblenden- und die E/A-Frontanschlüsse mit Ihrem Motherboard. Connecter l’ ATX 24 broches, le EPS 8pin/ATX 4pin et les prises additionnelles à la carte mère. Enchufe los conectores ATX de 24 pines, EPS 8 pines/ATX 4 pines, del panel frontal y los conectores frontales de E/S a la placa base.
- Página 8 We recommend at this point to start thinking about routing the cables cleanly by fastening ATX 24pin and EPS 8pin/ATX 4pin cables on a bridge next to the power supply bracket. These two cables are designed to accommodate all possible connector location on a Mini-ITX motherboard so you may need to store excess cables in the area located on the right side of the hard drive cage.
- Página 9 We recommend to route the USB Рекомендуется прокладывать USB-кабели and audio front I/O cables around и аудиокабели к передним разъемам the front of hard drive cage, there ввода/вывода вокруг верхней части should be sufficient bridges for корзины для жестких дисков, там должно fastening the cables.
- Página 10 Install and secure 3.5” and 2.5” hard Установите 3,5-дюймовые и 2,5-дюймовые drives to the hard drive cage with жесткие диски в корзину и закрепите винтами. screws. The SG08’s drive cage is Корзина для жестких дисков SG08 совместима compatible with 2.5” hard drives with с...
- Página 11 In order to create enough space for power supply cables, the hard drive cage design is moved as far to the right as possible. So 90 degree angled SATA connector must be used, regular 180 degree SATA connector will prevent installation of top cover. Damit die Netzteilkabel genügend Platz haben, wird der Festplattenkäfig so weit wie möglich an der rechten Seite angebracht.
- Página 12 We recommend connecting all fan or SATA cables to the motherboard now as installation of graphics or expansion card may prevent installation of these cables. Wir empfehlen, nun alle Kühler- oder SATA-Kabel am Motherboard anzuschließen, da die Installation der Grafik- oder Erweiterungskarte die Verbindung dieser Kabel erschweren oder verhindern kann.
- Página 13 Remove expansion slot screws to Выверните винты слотов расширения, remove expansion slot covers. чтобы снять заглушки слотов. Lösen Sie zum Entfernen der 확장슬롯 나사를 풀어 확장슬롯 커버를 Abdeckung die Schrauben des 제거합니다. Erweiterungssteckplatzes. Retirer les vis des slots d’extension 拡張スロットのネジを外して拡張 pour retirer les caches.
- Página 14 Reinstall top expansion slot cover Установите заглушку верхнего слота back to the case and secure with расширения обратно в корпус и закрепите screws. винтами. Bringen Sie die Abdeckung des 상부 확장 슬롯 커버를 재설치한 후 나사로 oberen Erweiterungssteckplatzes 고정시킵니다. wieder am Gehäuse an und befestigen diese mit Schrauben.
- Página 15 Install the optical drive bracket back into the case then align the slim optical drive face plate with the front panel and secure with screws. Installieren Sie die Halterung des optischen Laufwerks wieder im Gehäuse und richten die Vorderseite des schmalen optischen Laufwerks an der Frontblende aus und befestigen Sie sie mit Schrauben.
- Página 16 Install the fan bracket back into the case and secure with screws. (make sure the frame of the fan is covering the power supply plug from the inside). Installieren Sie die Kühlerhalterung wieder im Gehäuse und befestigen sie mit Schrauben. (stellen Sie sicher, dass der Rahmen des Kühlers den Netzteilstecker von innen abdeckt).
- Página 17 Place the top cover back onto the Установите верхнюю крышку обратно case and secure with screws. на корпус и закрепите винтами. Platzieren Sie die obere Abdeckung 상부커버를 케이스에 재 설치한 후 나사로 wieder am Gehäuse und befestigen 고정시킵니다. diese mit Schrauben. Remettre en place le capot ケースに上部カバーを戻し、...
-
Página 18: Component Size Limitations
Component size limitations Although the SG08 is small, it is still compatible with many oversized components, please refer to the following guidelines for component selection and future upgrade considerations. 117mm (1) CPU cooler height limitation 117mm 140mm (2) Power supply length limitation 140mm Please note that the power supply included with the SG08 has been designed specifically for the case. - Página 19 Component size limitations Although the SG08 is small, it is still compatible with many oversized components, please refer to the following guidelines for component selection and future upgrade considerations. Notare che l’alimentatore incluso con SG08 è stato disegnato in modo specifico per il case. Anche se le dimensioni rispettano lo standard ATX, il numero di cavi è...
- Página 20 Component size limitations Although the SG08 is small, it is still compatible with many oversized components, please refer to the following guidelines for component selection and future upgrade considerations. (3) Graphics card/expansion card length limitation SG08 can support 12.2”(310mm) consumer level graphics cards Due to design, the graphics or expansion card when installed will be situated very close to the power supply so we recommend using cards with backside components no taller than 3.21mm.
- Página 21 Recommended cooling device setup and selection Using SilverStone’s NT06-E without CPU fan is possible on CPU with TDP rated up to 95W. With a 120mm fan installed on the NT06-E, the use of a CPU with TDP rating of up to 140W is possible. We recommend using SATA connector with 90 degree angle for the 3.5” hard drive in order to use larger CPU cooler such as SilverStone’s NT06-E or bigger.
- Página 22 Recommended cooling device setup and selection make sure the VGA duct matches the intake fan on the card. When installing high-end graphics card: The SG08 comes with a VGA duct, please install it as shown in the illustration (make sure the location matches the intake fan on the card). The VGA duct is designed only for dual slot graphics cards and for cards with heatsink cover.
- Página 23 Recommended cooling device setup and selection VGA duct installation Look for the VGA duct and the EVA Найдите VGA-короб и форму EVA в foam from the accessories box. коробке с принадлежностями. Entnehmen Sie dem Zubehörkarton den VGA- VGA덕트와 EVA 폼을 악세사리 Belüftungskanal und den EVA-Schaum.
- Página 24 Recommended cooling device setup and selection There are more vents on the side cover, which gives you more freedom to place the VGA duct in support of graphics card regardless of airflow direction and length. Die SG08-Version ohne Fenster verfügen, befinden sich mehr Belüftungsöffnungen an der seitlichen Blende; dies bietet mehr Freiheit zur Platzierung des VGA-Belüftungskanals in Verbindung mit Grafikkarten - unabhängig von der Richtung und Reichweite des Luftstroms.
- Página 25 Recommended cooling device setup and selection Cable routing We placed pass-through holes on the back of the case, please use wire ties in places as needed by your hardware configuration. Hinter dem Motherboard-Einschub befinden sich Haken, die der Verwendung von Kabelbändern dienen. Il y a des crochets derrières le support de la carte mère pour utiliser des attaches pour regrouper les câbles.
- Página 26 Recommended cooling device setup and selection Fan speed adjustment SG08’s 180mm fan can be adjusted to run at 700rpm or 1200rpm according to your needs. 180mm fan speed switch explanation: “L” denotes fan running at low speed. “H” denotes fan running at high speed.The included fan is a completely redesigned “Air Penetrator”...
-
Página 27: Maintenance And Upgrade
Maintenance and upgrade (1) Fan and fan filter disassembly guide If you need to change fans, clean, or upgrade a fan, please refer to the following steps: Unscrew screws holding the fan bracket Выкрутите крепежные винты кронштейна and then pull up and away from the case. вентилятора, а... - Página 28 Maintenance and upgrade Unscrew four screws holding the fan and two screws holding the graphics/expansion card security brace. When reinstalling both items, be sure to install them in the correct orientation. Lösen Sie die vier Schrauben des Lüfters und die zwei Schrauben der Sicherheitshalterung der Grafik-/Erweiterungskarte. Achten Sie auf die korrekte Ausrichutng, wenn Sie beide Komponenten wieder anbringen.
- Página 29 Maintenance and upgrade Reinstall the 180mm fan bracket, secure it with three screws. Refer to rear case marking of “L” and “H” position and fan speed switch’s wire guide when reinstalling and securing the fan speed switch back onto the case. Bringen Sie die 180 mm-Lüfterhalterung wieder an;...
- Página 30 Maintenance and upgrade (2) Fan filter cleaning guide После снятия верхней крышки корпуса After removing the top cover of the case, фильтр вентилятора размером 180 мм the 180mm fan filter can slide out easily. свободно выдвигается. Nach der Entfernung der oberen 케이스의...