Original Instructions - Metabo DKP 310 Manual Original

Original instructions

1. Declaration of Conformity
Under our sole responsibility, we hereby declare
that these compressed-air cartridge presses, iden-
tified by type and serial number *1), meet all rele-
vant requirements of directives *2) and standards
*3). Technical documents for *4) - see Page 3.
2. Specified Use
The device is designed to extrude sealant or adhe-
sive from cartridges in the professional sector.
It is not designed for foodstuffs or for medical/veter-
inary purposes. It should not be used with pressur-
ized cartridges. The gun should also not be used as
a lifting/spreading tool.
This air tool must only be operated with a com-
pressed air supply. The maximum supply pressure
specified on the air tool must never be exceeded.
The tool must not be operated using explosive, in-
flammable or hazardous gases.
Any other use does not comply with the intended
purpose. Unspecified use, modification of the air
tool or use of parts that have not been tested and
approved by the manufacturer can cause unfore-
seeable damage.
The user bears sole responsibility for any damage
caused by improper use.
Generally accepted accident prevention regula-
tions and the enclosed safety information must be
observed.
3. General Safety Instructions
For your own protection and for the
protection of your air tool, carefully
observe all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety warn-
ings and instructions may result in electric shock,
fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your air tool only together with these docu-
ments.
- The user or user's employer must evaluate the specific risks associated with each application of
the tool.
- The safety instructions must be read and under-
stood before installing, operating, repairing or
maintaining the tool, and also before replacing any
accessory parts or carrying out any work in the
vicinity of the air tool. Failure to read and follow the
instructions may lead to serious injury.
- Only qualified, trained operators are authorised to
install, adjust or use the air tool.
- The air tool must not be modified. Any modifica-
tions implemented may reduce the efficiency of
the safety measures and increase risks for the
operator.
- Never use air tools that have been damaged. Look
after your air tools carefully. Regularly check that
all moving parts are functioning correctly and do
not jam. Also ensure that no parts are broken or
damaged to an extent that they affect the opera-
tion of the air tool. Check that all signs and labels
are legible and intelligible. Have damaged parts
repaired or replaced before using the device.
Many accidents are caused by poorly maintained
air tools.
4. Special Safety Instructions
4.1 Risks associated with ejected parts
- Disconnect the air tool from the compressed air
supply before replacing the mounted tool or
accessory parts, and also before carrying out
repairs or settings.
- If either the workpiece, accessory parts or the air
tool breaks, parts may be ejected at high speed.
- While operating, maintaining or repairing the air
tool, or replacing accessory parts, you must
always wear impact-resistant safety goggles. The
degree of protection required for each individual
task must be evaluated separately in each case.
- Also ensure that no other people are placed at
risk.
4.2 Risks during operation
- The operator and maintenance staff must be
physically capable of handling the size, weight
and power output of the air tool.
- Make sure you hold the air tool correctly: since
you must be prepared to counter any standard or
unexpected movements, keep both hands ready.
- Ensure you stand in a safe position and keep your
balance at all times.
- Avoid accidental operation. If the air supply is
interrupted, switch off the air tool using the On/Off
switch.
- Only use lubricants that have been recommended
by the manufacturer.
- Wear personal protective equipment and always
wear safety glasses. By wearing personal protec-
tive equipment such as gloves, protective
clothing, a dust mask, non-skid safety shoes, a
safety helmet or ear protectors, to suit the type of
device and its use, you reduce the risk of injury.
Wearing this equipment is recommended.
4.3 Risks associated with recurring move-
ments
- When working with the air tool, you may experi-
ence an uncomfortable sensation in your hands,
arms, shoulders, neck or other body parts.
- Make sure you are in a comfortable position to
carry out work with the air tool, check that the tool
is held securely, and avoid any awkward positions
that make it difficult, for example, to keep your
ENGLISH en
9