Idiomas disponibles
Idiomas disponibles
GB
Installation of the PLAY bathtub with plastic front panel
Fig. 1
Mounting procedure
To assemble the bathtub with the panel, use all the parts in the basic bathtub mounting kit plus the panel
accessories included in the PANEL and PANELKIT kits.
When installing the bathtub, item
B
, supplemented by the following instructions, apply to the full extent.
1.
Turn the bathtub upside down and place the cardboard parts of the packaging together with Styrofoam
on the corners so that the rim of the bathtub.
2.
The bathtub with the panel has 3 metal supports. Bolt the threaded rods (
outer openings in the supports by the inclined side. Mount the threaded rod ( ) (length 50 mm) with the
supporting leg to the other end of the support ( ) (length 850 mm). Permanently mount the separate
supporting legs with a screw 125 mm long before fastening the supports. ATTENTION! The metal supports
are universal and may have more openings. When attaching them to the bathtub, use only the Ø 3 mm
openings by the reinforced bottom, the Ø 12.5 mm openings for the supporting legs and the threaded rods
according to the figure.
3.
Mount the panel holder (
104
tighten the nuts; allow some clearance for mounting and adjusting.
4.
Place the completed supports on the reinforced bottom of the bathtub and bring them into position.
Trace the position of the supports on the bottom of the bathtub (
5.
Using a water level or set squares, measure the exact distance between the axis of the outer opening in
the support and the bathtub contour and shift the support so that the center of the opening in the long
threaded rod (
101
) is 40-45 mm from the bathtub edge and that the panel holder (
mm from the outer bathtub edge.
6.
Trace the contours of the Ø 6 mm openings in the metal supports on the bottom of the bathtub. Put the
supports to one side and, using the enclosed drill bit, drill the Ø 3 mm fastening holes. ATTENTION drill
only within the reinforced part of the bottom to a depth of 10 mm using a stop so that you don't damage the
plastic of the bottom of the bathtub.
7.
Put the supports back and bolt them using the screws ( ). It is recommended to use cement under the
support edges touching the bathtub.
8.
Adjust the position of the threaded rod with the holder (
the bathtub. Apply a sufficient amount of cement to the marked spot on the bathtub rim under the support
(
103
). Tighten the nuts (
102
) on the support applying a little pre-stress so that the upper edge of the
bathtub does not become deformed.
9.
Adjust the height of the panel holder (
edge and matches the shape of the outer outline. To stabilize the lower part of the panel, mount the holder
(
105
) under the support as a prop using the washer (
10.
Place the bathtub in its final location and, using a water level, adjust it in the horizontal position.
ATTENTION: for a bathtub with a panel, measure the distance between the floor and the bathtub cut line
as 577 mm.
11.
Slide the panel into the holders on the bathtub and level it. Trace the panel contour on the floor and on
the side walls. Check the functioning of the supports (
12.
After removing the panel, adjust the position of the support (
supporting legs ( ) and of the panel holders (
6
13.
Trace the upper bathtub edge on the walls and bolt the clips for the bathtub rim ( ) according to the
bathtub installation manual, item 16.
14.
To fasten the panel to the side walls, two holders (
right. Place the holder (
107
) on the panel contour at the selected spot. Move the panel holder downwards,
under the bathtub, by the thickness of the panel, i.e. 3 to 4 mm from the panel contour and trace the centers
of the oval mounting openings on the wall. Drill Ø 8 mm holes at the marked centers, insert the dowels
(
108
), and bolt the panel holders (
panel contour on the wall.
15.
Mount the drain set on the bathtub. For soundproofing, it is recommended to attach a plastic foam band
of approximately 10x6 mm on the bathtub sides adjacent to the wall.
16.
Place the bathtub back in its final location and suspend it on the plastic clips according to the bathtub
installation manual. Insert the front panel (
openings (at the center of the perforated sheet) on the panel at the positions of the side holders (
17.
Using a Ø 3 mm drill bit, drill a hole through the panel and the perforated sheet. Be CAREFUL not to
damage the plastic panel with the drill chuck! Fasten the panel using the self drilling screw (
plastic washer (
52
); press the plastic cap (
18.
If necessary, it is possible to cement the joints between the panel and the tiles or, possibly, the
horizontal joints. After cementing the bathtub to the tiles, or after mounting the bathtub laths, it is
recommended to fill the bathtub with approximately 100 liters of water and leave it until the next day until
the cement sets.
RAVAK a.s., Obecnická 285, 261 01 Pøíbram, ÈR tel.: 318 427 111, fax: 318 427 269
101 Threaded rod M 12x550 mm
102 M 12 nut
103 Threaded rod support no. 17
104 Panel holder no. 15
105 Panel holder no. 10
106 Washer Ø 13
107 Panel holder lateral
108 Dowel, Ø 8
109 Dowel screw, Ø 4x40
110 Self-tapping screw, Ø 3.5x13
52 Plastic washer, Ø 4
53 Plastic cap, Ø 4
1600
A
CONSTRUCTIONAL READINESS of the bathtub manual and item
1
) between two nuts (
102
) on the other end of the threaded rods (
7
104
104
) so that the panel, after sliding in, is just below the bathtub cut
106
) and secure it with the nut (
105
) in the lower part of the panel.
104
).
107
) are used for the left bathtub edge and two for the
107
) using the screws (
109
51
) into the holders and level it. Mark the centers of the fastening
53
) on the bolt head (
e-mail: [email protected]
MOUNTING KIT - PANEL KIT
70°
101
) (length 550 mm) to the
4
5
Fig. 1
).
104
) is approximately 3
); trace the position of the support (
102 Fig. 2
) (
105
); check and secure the position of the
9
). Mark the axes of the panel holders on the
Fig. 3
).
www.ravak.com
MOUNTING KIT - PANEL
2 pcs
51 Play panel 160x160
10
pcs
2
pcs
2
pcs
2
pcs
2
pcs
4
pcs
8
pcs
8
pcs
Fig. 2
4
pcs
4
pcs
4
pcs
102
101
1, 2
101
). Do not
5
6
103
) on
Fig. 3
).
Bathtub rim
108, 109
107
).
110
) with the
108, 109
1 pc
40 - 45
SILICONE
103
104
51
102
106
105
107
110
51
53
52
107
110
53
52
