YATO YT-85700 Manual De Instrucciones página 14

GB
Make sure that all preparatory operations have been carried out in a correct way.
Make sure that the vacuum cleaner switch remains in the off position - "O".
Plug the power cord into the mains socket, and then turn the switch to the on position - "I" (XIII).
The brush is fi tted with a lever that slides off the bristles. The bristles should be slid off when cleaning smooth, hard surfaces. It is
recommended to clean carpet fl oorings and carpets with hidden bristles.
After the work is fi nished, switch off the vacuum cleaner with a switch, and then disconnect the power plug from the mains socket.
Proceed to operations that preserve the vacuum cleaner.
Emptying the container of vacuum cleaner (XIV)
After the dry vacuum cleaning is fi nished, dismantle the cover and check the bag's fi lling level. If the bag is full, it should be re-
moved and replaced with a new one.
After the wet vacuum cleaning is fi nished, dismantle the cover of vacuum cleaner. The container has been fi tted with a cover
placed near its base. Opening the cover will cause the emptying of the container.
Impurities remaining in container can be removed by tilting the container. After having it emptied, clean the container with a water
jet. Close the cover and then dry thoroughly.
Built-in electrical socket
The vacuum cleaner features a built-in electrical socket, which is used to supply the power tools belonging to I and II class of
electrical insulation.
This allows for easier use of the vacuum cleaner in the form of system of extraction of dust generated during the work. Voltage
appears in the socket when the plug of power cord supplying the vacuum cleaner is connected to the mains socket. Therefore,
before connecting the vacuum cleaner to power supply and the power tool to the vacuum cleaner socket, make sure that switches
of both devices remain in the off position.
After connecting the vacuum cleaner to the outlet of power tool's dust extraction (a suitable adapter may be needed for this, that is
not delivered with the vacuum cleaner) and the power tool plug to the vacuum cleaner socket, the vacuum cleaner may be started
by turning the switch to the "I" position, the vacuum cleaner will start working regardless of the operation of power tool and it will
continue to work until the switch is turned to the "O" position.
An automatic mode is the recommended operating mode. To this end, after connecting the vacuum cleaner to the outlet of power
tool's dust extraction, and the power tool plug to the vacuum cleaner socket, turn the switch to the "II" position. The vacuum clean-
er will switch on automatically after a short time from the start-up of power tool and will also switch off automatically after a short
time from switching off the power tool.
Regardless of the selected mode of operation, after the work is fi nished, switch off the vacuum cleaner by turning the switch to the
"O" position, and then disconnect the vacuum cleaner plug from the mains socket, unplug the power tool from the vacuum cleaner
socket and proceed with maintenance operations.
Note! If during operation suspicious vibrations, drop in suction force or louder operation of the engine are observed, this may in-
dicate that the container is full or the hose, extension tubes or suction nozzle are clogged. In this case, immediately switch off the
vacuum cleaner with the switch and unplug the power cord from the mains socket. Then empty the container and check patency
of hose and endings. If necessary, unclog it. If it is not possible to unclog the hose, extension pipes or suction nozzle replace them
with new ones before continuation of work.
Note! When using the vacuum cleaner as a blower, make sure that the container has been emptied of all waste, the bag has been
removed and the fi lter cleaned or replaced with a new one. There is a risk of impurities collected in the container or in the bag
being sucked in through the outlet orifi ce.
Vacuum cleaner maintenance
Note! Before proceeding with any maintenance operations, make sure that the power cord plug has been disconnected from the
mains socket.
Each time, when using the vacuum cleaner, please check the container, cover gasket and air fi lters as described in point: "Prepa-
ration to work".
Clean the vacuum cleaner from the outside using a jet of compressed air at a pressure not more than 0.3 MPa. In particular, pay
attention to patency of vents, both inlet and outlet. If it is necessary, clean it using a jet of compressed air at a pressure not more
than 0.3 MPa. Do not use sharp, metal objects to clean the vents. Do not immerse the vacuum cleaner in water to clean it. Check
the vacuum cleaner hose before and after each use for damages. It is forbidden to use damaged hose. In case of sucking in water
or wet impurities, clean the inside of vacuum cleaner, the fl exible hose, extension pipes and the endings immediately after the
work is fi nished. Dried impurities can lead to irreversible damage to the vacuum cleaner or its components.
The inside of the hose and extension pipes should be cleaned with a stream of water, after disconnecting from the vacuum clean-
er, and then allow them to dry before next use. Remove larger soiling from the cover with a soft cloth.
O R I G I N A L I N S T R U C T I O N S
14