Device Operation - YATO YT-85715 Manual Del Usuario

GB
Check the condition of connector on a regular basis. It is forbidden to use the vacuum cleaner with the hose damaged.

DEVICE OPERATION

Preparation to work
Check the vacuum cleaner container, empty it from waste if necessary.
Check the condition of fi lters. If the fi lters intended for dry cleaning (paper) and a nonwoven fi lter are dirty, they should be cleaned
only with a stream of compressed air of a pressure not higher than 0.3 MPa. If impurities cannot be removed from fi lters, they
must be replaced with new ones. Filters designed for wet cleaning (sponge) can be cleaned by immersing them in lukewarm water
with addition of soap. After cleaning, rinse them in clean water and squeeze out the excess of water. Do not twist. Allow them to
dry before use.
Check the condition of gaskets, if any damage is found, gaskets should be replaced with new ones.
NOTE! It is forbidden to work with a vacuum cleaner without properly installed air fi lter. This may lead to damaging the vacuum
cleaner and also cause an electric shock.
The base of vacuum cleaner features possibility of mounting the casters. Attach the front swivel casters by inserting the caster
plugs into holes in the base of container (II). Rear casters have been fi tted in factory.
Raise the rear handle, it will facilitate moving the vacuum cleaner during the work. Folded handle makes it easier to store the
vacuum cleaner.
The vacuum cleaner has been fi tted with two separate containers. Top container is used only for dry cleaning, fi tted with a reusable
bag. Lower container is used for both wet and dry cleaning. Lower container does not have the possibility to install the bag, but a
fi lter must be replaced depending on the type of selected operation.
The fi lter is placed in the front part of the container's cover. Insert the fi lter frame into the guides (III).
The fi lter made of paper is intended for dry cleaning. The fi lter made of a sponge is designed for wet cleaning.
Do not use the wrong type of fi lter. Using a fi lter designed for dry cleaning for fi ltering during wet cleaning will lead to damaging
the fi lter, which may lead to damaging the vacuum cleaner. Using a fi lter designed for wet cleaning for fi ltering during dry cleaning
will not provide the correct level of fi ltering, which may lead to damaging the vacuum cleaner.
The vacuum cleaner cover has been fi tted with a fl oat (IV), which cuts off the supply of air every time the tank overfl ows. Before
the start of work, make sure that the fl oat and guides in which it is moving have not been damaged, are clean and ensure free fl oat
movement. Each fl oat activation is signalled by louder motor operation and a drop in suction power.
Note! It is forbidden to use a vacuum cleaner without a properly functioning fl oat.
The upper tank is fi tted with a separate cover, to which the bag should be attached. The cover can be opened by pressing the
release button of the cover latch (V). The bag's inlet should be slid over the inner part of hose fastening (VI) so that the gasket
around the bag's orifi ce is fully attached to the hose fastening. The bottom edge of the bag is fi tted with a closure that allows for
bag emptying. Before attaching the bag to the container, make sure that the bag has been closed (VII).
Attach the lid onto the upper edge of vacuum cleaner container so that it adheres with its entire circumference. Using latches,
hold the lid tight against tank. Please note that there are marked points on the lid that allow obtaining proper tightness of fastening
(VIII).
Connect the fl exible hose to the inlet orifi ce. Hose connection should be slid into the orifi ce so that the cuts on it hit the protrusions
of the inlet orifi ce and then turn in direction pointed by arrow marked „CLOSE" (VI). Make sure the hose would not slip off during
operation.
The inlet orifi ce that is not used for work should be sealed with the cover delivered with product. Attach the cover in the same way
as the hose: insert and turn (IX). Leaving the second orifi ce unplugged will cause the vacuum cleaner performance to drop and
may cause unintentional suction of objects into the vacuum cleaner container.
Connect the two parts of pipe together by inserting the narrower end of pipe into the wider one (X). Then connect the pipe to free
end of the elastic hose, also inserting the narrower end of hose into the wider end of pipe (XI).
In the same way, attach the accessory in form of a brush or a narrow sucker (XII) to free end of the pipe.
Select proper accessory for the selected type of work. The brush is intended for cleaning large and fl at surfaces, and a narrow
sucker for places that cannot be reached using a wide nozzle.
In order to dismantle the hose, turn its connector in direction pointed by arrow marked „OPEN", and then slide off the connection
out of inlet orifi ce. Dismantling of extension pipes and nozzles should be carried out the other way round than assembly.
The vacuum cleaner allows connecting the hose also to the outlet orifi ce, so it can used as a blower. The hose is connected in a
O R I G I N A L I N S T R U C T I O N S
13