Idiomas disponibles
Idiomas disponibles
important
Safety
instructions
The power supply cord with
this air conditioner contains a current
detection device designed to reduce the risk of
fire.
Please refer to the section'Operation of
Current Device' for details.
In the event that the power supply cord is
damaged, it cannot be repaired, and it must
be replaced with a cord from the Product
manufacturer.
Avoid fire hazard or electric
shock. Do not use an extension cord or an
adaptor plug. Do not remove any prong from
the power cord.
Power supply cord
with 3-prong grounding
plug and current
detection device
Read all instructions
before using this air conditioner.
For Your Safety
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this
or any other appliance.
Read product labels for flammability
and other warnings.
Prevent Accidents
To reduce the risk of fire, electrical
shock, or injury to persons when using your air
conditioner,
follow
basic precautions,
including
the following:
Be sure the electrical
service is adequate
for the model you have chosen. This
information
can be found on the nameplate,
which is located
on the side of the
cabinet.
If the air conditioner
is to be installed
in a window,
you will probably
want to
clean both sides of the glass first. If the window
is a triple-track
type with a
screen panel
included,remove
the screen completely
before
installation.
Be sure the air conditioner
has been securely and correctly
installed
according
to the separate
installation
instructions
provided
with this manual.
Save this
manual
and the installation
instructions
for possible
future use in removing
or
reinstalling
this unit.
When handling
the air conditioner,
be careful
to avoid
cuts from sharp metal
fins on front and rear coils.
Electrlcal information
The complete electrical
rating of your new room air conditioner
is stated on the serial
plate. Refer to the rating when checking the electrical
requirements.
Be sure the air conditioner
is properly
grounded.
To minimize shock and fire
hazards, proper
grounding
is important.
The power cord is equipped
with a
three-prong
grounding
plug for protection
against shock hazards.
Your air conditioner
must be used in a properly
grounded
wall receptacle.
If the
wall receptacle
you intend to use is not adequately
grounded
or protected
by a
time delay fuse or circuit breaker,
have a qualified
electrician
install the proper
receptacle.
Do not run air conditioner
without outside protective cover in place. This could
result in mechanical
damage
within the air conditioner.
Do not use an extension
cord or an adapter
plug.
READ THiS SECTION BEFORE ATTEMPTING
TO OPERATE AiR CONDiTiONER.
Unit must be upright
for one hour prior to operating.
Operation
of Current
Device
Plug in &
press RESET
The power
supply cord contains a current device
that senses damage
to the
power cord.
To test your power supply
cord do the following:
1. Plug in the Air Conditioner.
2. The power supply cord will have TWO
buttons on the plug head. Press the
TEST button. You will notice a click as the RESET button pops out.
3. Press the RESET button. Again
you will notice a click as the button engages.
4. The power supply cord is now supplying
electricity
to the unit. (On some
products this is also indicated
by a light on the plug head).
NOTES:
• Do not use this device to turn the unit on or off.
• Always
make sure the RESET button is pushed in for correct
operation.
• The power supply
cord must be replaced
if it fails to reset when either the
TEST button is pushed,
or it cannot be reset. A new one can be obtained
by
contacting
Sears at 1 -800-4-MY-HOME
®.
• If power supply cord is damaged,
it CANNOT
be repaired.
It MUST be
replaced
by one obtained
by contacting
Sears at 1-800-4-MY-HOME
®.
4
