Using The Tool; Placing Tool In Service - Facom V.103MF Guía De Instrucciones

EN
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.

PLACING TOOL IN SERVICE

• Always operate, inspect and maintain this tool in accordance
with all regulations (local, state, federal and country), that may
apply to hand held/hand operated pneumatic tools.
• For safety, top performance, and maximum durability of parts,
operate this tool at 90 psig (6.2 bar/620 kPa) maximum air
pressure at the inlet with 3/8" (10 mm) inside diameter air
supply hose.
• Always turn off the air supply and disconnect the air supply
hose before installing, removing or adjusting any accessory on
this tool, or before performing any maintenance on this tool.
• Do not use damaged, frayed or deteriorated air hoses and
fi ttings.
• Be sure all hoses and fi ttings are the correct size and are tightly
secured.
• Always use clean, dry air at 90 psig maximum air pressure.
Dust, corrosive fumes and/or excessive moisture can ruin the
motor of an air tool.
• Do not lubricate tools with fl ammable or volatile liquids such as
kerosene, diesel or jet fuel.
• Do not remove any labels. Replace any damaged label.
• The use of a hose whip is recommended. A coupler connected
directly to the air inlet increases tool bulk and decreases tool
maneuverability.
• For maximum performance, the coupler on the wall should be
the next size larger than the coupler used on the tool. The coupler
closest to the tool should not be less than the proper air supply
hose size.
The use of other than genuine replacement parts may result in safety hazards, decreased tool performance, and increased
FACOM
maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest
NU-V.103MF_0309.indd 6-7 NU-V.103MF_0309.indd 6-7
WARNING

USING THE TOOL

• Always wear eye protection when operating or performing
maintenance on this tool.
• Always wear hearing protection when operating this tool.
• Keep hands, loose clothing and long hair away from rotating
end of tool.
• Anticipate and be alert for sudden changes in motion during
start up and operation of any power tool.
• Keep body stance balanced and fi rm. Do not overreach when
operating this tool. High reaction torques can occur at or below
the recommended air pressure.
• Air powered tools can vibrate in use. Vibration, repetitive mo-
tions or uncomfortable positions may be harmful to your hands
and arms. Stop using any tool if discomfort, tingling feeling or
pain occurs. Seek medical advice before resuming use.
• Use accessories recommended by FACOM.
• This tool is not designed for working in explosive atmospheres.
• This tool is not insulated against electric shock.
NOTICE
Authorized Servicenter.
FACOM
WARNING
WARNING LABEL IDENTIFICATION
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
WARNING
Always wear eye protection when operating or
performing maintenance on this tool.
WARNING
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may be
harmful to your hands and arms. Stop using any tool if
discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
WARNING
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any
maintenance on this tool.
PLACING TOOL IN SERVICE
LUBRICATION
FACOM NS.557-04
Always use of an air line lubricator with these tools. We recommended the
following Filter-Lubricator-Regulator Unit: FACOM N.553D.
After each eight hours operation, unless the air line lubricator is used, detach
the air hose and inject about 1-1/2 cc of oil into the inlet busching.
After each forty-eight hours of operation, or as experience indicates, remove
the Oil Chamber Plug and fi ll the mechanism oil chamber with the recommen-
ded oil FACOM NS.557-04.
WARNING
Always wear hearing protection when operating
this tool.
WARNING
Do not carry the tool by the hose.
WARNING
Keep body stance balanced and fi rm. Do not overreach
when operating this tool.
WARNING
Operate at 90 psig (6.2 bar/ 620 kPa) Maximum air
pressure.
WARNING
Do not use damaged, frayed or deteriorated air hoses
and fi ttings.
04/03/2009 16:12:40 04/03/2009 16:12:40