Digital Effect Processor - Phonic AM442D Manual Del Usuario

24. EFX Control
This control alters the signal level that is sent to the
EFX send (AUX 2 on the AM 442D, AUX 3 on the
AM 642D/AM 642DP) output and the built-in digital
effect processor. The EFX send signal can be used in
conjunction with external signal processors (this signal
of which can be returned to mixer via the AUX return
input), or simply as an additional auxiliary output.
25. Pan / Balance Controls
This alternates the degree or level of audio that the
left and right side of the main mix should receive. On
Mic channels, the PAN control will adjust the level
that the left and right should receive (pan), where as
on a stereo channel, adjusting the BAL control will
attenuate the left or right audio signals accordingly
(balance).
26. O n B u t t o n a n d
Indicator
This turns the channel
on, allowing the user to
use the feed from the
channel's inputs to supply
the MAIN L/R, GROUP 1/2,
AUX and EFX buses. The
corresponding indicator
will be illuminated when
turned on.
27. 1-2 and L/R Buttons
These handy buttons allow you to decide the audio
path of the corresponding channel. Pushing the "1-2"
button allows the signal to be sent to the Group 1-2
mix, where the "L/R" allows it to be sent to the Main
L/R mix.
28. Peak Indicator
This LED indicator will illuminate when the channel hits
high peaks, 6 dB before overload occurs. It is best to
adjust the channel level control to a level slightly prior
to the peak indicator does not light up. This will ensure
a greater dynamic range of audio. This indicator also
doubles as a Solo indicator, when the SOLO button
is engaged.
29. Solo Button
The Solo button is pushed to allow the signal of a
corresponding channel to be sent to the Control Room
/ Phones control. The signal is either that of a pre- or
post-fader depending on the pre/post button in the
master section.
30. Level Faders
These faders allow users to adjust the level of the
signal from the corresponding input channel that is
to be sent to the destinations selected by the 1-2 and
L/R buttons.
6

Digital Effect Processor

31. Digital Effect Display
This 2-digital numeric display shows the program
number that is currently applied to your EFX audio
signal. When you rotate the Program control, you can
scroll through different program numbers; however
the display will revert back to the original program if
a new program is not selected within a few seconds.
For a list of available effects, please observe the
Digital Effect Table.(When the Digital Effect Processor
is put into stand-by mode (by use of the foot switch or
on button) the 2 small dots within the numeric display
will fl ash. In this mode, users are still able to preview
and select new effect programs.)
32. Sig and Clip Indicators
Located within the Digital Effect Display are Clip
and Sig LEDs. The Sig LED will light up when any
signal is received by the effect processor, and the
Clip LED will light up shortly before excessive signals
are dynamically clipped. If the Clip LED lights up too
often, it may be advisable to turn down one or all EFX
controls on input channels to ensure the signal level
is not too high.
33. Program Control
This control is used to scroll through the various
effects. Turning the control clockwise will allow users
to ascend into higher program numbers, and turning
it counter-clockwise will allow users to descend
into lower program numbers. Pushing this control
will apply the new effect. When a tap-delay effect
is selected, pressing this control will allow users to
select the tap-delay time.
By pushing the button several times, the effect
processor interprets the time between last two
pushes and remembers this as the delay time, until
the button is pushed again (this is kept, even after
the power is turned off). When the tap delay effect is
selected, a small LED will fl ash within the digital effect
display window at the selected intervals.
34. DFX On Button and Indicator (AM642D/
AM642DP only)
This button will turn the Digital Effect processor on
and off. Activation of the Effect Processor will cause
the accompanying LED indicator to light up.
AM442D / AM642D / AM642DP