Blackstone 1863 El Manual Del Propietario página 7

Model 1863 | Owner's Manual | Assembly Guide
S T E P 0 5
then secure it to the unit with one shear pin and one cotter pin.
S T E P 0 6
left side shelf by screwing them into the precut holes. Repeat this step with
the right side shelf using four (4) side shelf pegs and four (4) peg washers.
S T E P 0 7
to the right side of the griddle unit. Repeat this step on the left side of the
griddle unit with two (2) shelf fixing plates and four (4) M6X12 screws.
10
Place the upper propane tank hanger between the brackets and
Attach the four (4) side shelf pegs and four (4) peg washers to the
Using four (4) M6X12 screws, attach two (2) shelf fixing plates
Section 01
BAT TERY POWERED IGNITION
TROUBLESHOOTING
SYMPTOMS
01. Burner will not Light with ignition system
CLEANING THE GRIDDLE COOKING SURFACE
S T E P 0 8
Using four (4) M8 screws, attach the side shelf to the shelf fixing
02. Pressing the ignition button does not result in a clicking sound
plates on the right side of the griddle unit. Repeat this step on the left side of
the griddle unit with four (4) M8 screws.
If ignition does not occur in 5 seconds, turn the burner controls off, wait 5
S T E P 0 1
minutes and repeat the lighting procedure. If this does not work, to deter-
each use, cool griddle below 300° F.
mine the cause, please try to ignite your griddle with a match. (Please
Scrape food debris with spatula or
reference the Match Lighting Instructions in the Cleaning the Burner
straight metal scraper.
Assembly section of the Care & Maintenance chapter.)
S T E P 0 2
surface with paper towel.
If you CAN ignite your griddle with a match
POSSIBLE CAUSES SOLUTION
01. Dead battery or no battery. Replace with new battery.
S T E P 0 9
Push the four (4) control knobs on the front of the unit.
02. Battery installed incorrectly. Ensure that the battery is installed nega-
S T E P 0 3
the help of another person , place the griddle top by aligning the pegs with
tive end first.
into approximately 6" sections
the precut holes in the unit. Connect the 20lb propane tank (not included).
(width of scraper tool). Apply a
(Please reference the Connection & Removal section of the Fuel | Propane – 03. Igniter wire misaligned. Ensure that the igniter wire is posi-
small amount of water onto first
tioned 1/8" to 1/4" away from the burner
20lb. Tank chapter.)
section with a bottle and then
tube, positioned above a burner hole.
scrape the water and debris toward
04. Damage to the ignition system. Contact customer service for replace-
the grease trap. Move to the next 6"
ment parts.
section and repeat.
DO NOT USE MORE THAN TWO
If you CAN NOT ignite your griddle with a match
TABLESPOONS OF WATER
POSSIBLE CAUSES AT A TIME. SOLUTION
05. Burner tubes are not Please reference the Gas Flow section of
1/4 cup of table salt may be used to
receiving propane. the Troubleshooting Chapter.
buff off stuck food residue.
S T E P 1 0
Proceed to the Griddle Seasoning Instructions section of the S T E P 0 4
Care & Maintenance chapter.
Enjoy cooking outdoors on your Blackstone 36" paper towel and dry completely.
Cooking Station!
S T E P 0 5
cooking oil to maintain seasoning
and protect the griddle top.
Care & Maintenance Assembly Guide | Owner's Manual | Model 1863
!
WA R N I N G
NEVER APPLY COLD
WATER ACROSS THE
WHOLE SURFACE OF A
HOT GRIDDLE AT ONCE.
This may cause warping.
To clean griddle after
!
C A U T I O N
DO NOT USE SOAP ON
THE GRIDDLE COOKING
SURFACE. This will destroy
the griddle's seasoning.
Wipe down griddle
With
Divide griddle surface
Insert one AA battery (not included)
into the battery socket with the posi-
tive terminal facing out, then screw
on the Ignition Button until tight. Be
careful to not over tighten.
Wipe again with a
NEED HELP?
Register your Blackstone product at
blackstoneproducts.com/register
and contact Blackstone Customer Service
for missing parts, assembly and operation
questions:
 PHONE:
Apply thin coat of
435-252-3030 ext 1
EMAIL:
[email protected]
ONLINE:
blackstoneproducts.com/pages/support
11