LG DLEY1201 Serie Manual De Propietario página 37

Before calling for service (cont.)
Problem
Clothes take too • Load is not properly sorted.
long to dry
• Large load of heavy fabrics.
• Dryer controls are not set properly.
• Lint filter needs to be cleaned.
• Exhaust ducts blocked, dirty, or duct run is
too long.v
• House fuse is blown, circuit breaker has
tripped, or power outage has occurred.
• Dryer is overloaded.
• Dryer is underloaded.
Clothes are shrinking • Garment care instructions are not being
followed.
Garments still wrinkled • Too many or too different types of garments
after Steam Fresh™ in dryer.
There are no creases • The function of this cycle is to remove
left on garment after wrinkles from fabric.
Steam Fresh™
Odors remain in clothing • STEAM FRESH™ did not remove odor
after STEAM FRESH™ completely.
CHECK FILTER light • Lint filter is almost clogged or full.
is on during the
drying cycle
TM
FLOW SENSE • Ductwork is too long or has too many turns/
indicator shows four restrictions.
bars during the drying • Significant blockage of the ductwork due to
cycle lint buildup or debris.
• The appliance has detected a restriction in
the external dryer venting.
The display shows • The duct work is about 90%-95% blocked.
"d90", "d95" ("d90" or "d95" error code displayed 2 hours
only)
• House exhaust system blocked.
Possible Causes
• Separate heavy items from lightweight items. Larger and heavier items take
longer to dry.
• Heavy fabrics take longer to dry because they tend to retain more moisture.
To help reduce and maintain more consistent drying times for large and heavy
fabrics, separate these items into smaller loads of a consistent size.
• Use the appropriate control settings for the type of load you are drying.
• Make sure the lint filter is cleaned before every load. With some loads that produce
high amounts of lint, it may be necessary to clean the filter during the cycle.
• Confirm that the exhaust ductwork is properly configured and free of debris,
lint, and obstructions. Make sure that outside wall dampers can open properly
and are not blocked, jammed, or damaged.
• Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the
problem is a circuit overload, have it corrected by a qualified electrician.
• Divide larger loads into smaller loads for drying.
• If you are drying a very small load, add a few extra items to ensure proper
tumbling action.
• To avoid shrinkage, please carefully follow the fabric care instructions for
your garment, because some fabrics will naturally shrink when washed. Other
fabrics can be washed but will shrink when dried in a dryer. Use a low or no
heat setting.
• Small loads of 1 to 5 items work best.
• Load fewer garments. Load similar-type garments.
• Use an iron to make creases.
• Fabrics containing strong odors should be washed in a normal cycle.
• Pause the drying cycle and clean the lint filter.
• Install a shorter or straighter duct run. See the Installation Instructions.
• Ductwork should be checked/cleaned soon.
Dryer can be used in this condition, but drying times may be longer.
• If exhaust restrictions are sensed by the FLOW SENSE
will remain on for two hours after the end of the cycle. Opening the door or
pressing the POWER button will turn off the display.
• Do not use the dryer until the exhaust system has been cleaned and/or
repaired. Using the dryer with a severely restricted exhaust is dangerous and
could result in a fire or other property damage.
• Check the outside dryer vent while the dryer is operating to make sure there is
strong airflow.
• If the exhaust system is extremely long, have it repaired or rerouted.
• Keep the area around the dryer clean and free of clutter.
• Check vent hood for damage or lint clogging.
• Make sure the area around the vent hood is clear.
TrOuBLEShOOTiNg
Solutions
TM
system, the indicator
37