Maintenance And Inspection - HIKOKI D 13VL Instrucciones De Manejo

English
SPECIFICATIONS
Voltage*
1
Power input
Speed range
No load speed
Steel
Capacity
Wood
Weight*
2
*1 Be sure to check the nameplate on product as it is subject
to change by areas.
*2 Weight: According to EPTA-Procedure 01/2003
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Insulated gripping surface
Fixing and removing side handle
Using depth gauge
Mounting and dismounting of
the bit
Selecting rotation direction
Switch operation
Locking-on the switch
Releasing the switch
Change rotation speed
Selecting accessories
Selecting the appropriate drill bit
○ When boring metal or plastic
Use an ordinary metalworking drill bit.
○ When boring wood
Use ordinary woodworking drill bit.
However, when drilling 6.5 mm or smaller holes, use a
metalworking drill bit.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits
Since use of an abraded drill bits will cause motor
malfunctioning and degraded effi ciency, replace the drill
bits with a new one or resharpening without delay when
abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes
For your continued safety and electrical shock protection,
carbon brush inspection and replacement on this tool
should ONLY be performed by a HiKOKI Authorized
Service Center.
(110 V, 120 V, 220 V, 230 V, 240 V)
860 W*
1
1 2
0 – 1100 min 0 – 3000 min
-1
13 mm 8 mm
40 mm 25 mm
2.9 kg
Figure Page
1
2
3
4
5
6
7
8
9
―
5. Replacing supply cord
If the replacement of the supply cord is necessary, it
has to be done by HiKOKI Authorized Service Center to
avoid a safety hazard.
CAUTION
In the operation and maintenance of power tools, the
-1
safety regulations and standards prescribed in each
country must be observed.
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country specifi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
IMPORTANT
Correct connection of the plug
The wires of the main lead are coloured in accordance
with the following code:
Blue: — Neutral
94
Brown: — Live
As the colours of the wires in the main lead of this tool may
94
not correspond with the coloured markings identifying the
94
terminals in your plug proceed as follows:
The wire coloured blue must be connected to the terminal
94
marked with the letter N or coloured black. The wire
coloured brown must be connected to the terminal marked
95
with the letter L or coloured red. Neither core must be
95
connected to the earth terminal.
NOTE:
95
This requirement is provided according to BRITISH
95
STANDARD 2769: 1984.
Therefore, the letter code and colour code may not be
96
applicable to other markets except The United Kingdom.
97
Information concerning airborne noise and vibration
The measured values were determined according to
EN60745 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 96 dB (A)
Measured A-weighted sound pressure level: 85 dB (A)
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN60745.
Drilling into metal:
Vibration emission value
Uncertainty K = 1.5 m/s
The declared vibration total value has been measured in
accordance with a standard test method and may be used
for comparing one tool with another.
It may also be used in a preliminary assessment of exposure.
WARNING
○ The vibration emission during actual use of the power
tool can diff er from the declared total value depending in
the ways in which the tool is used.
4
a
h , D = 5.4 m/s
2
2