GiBiDi EVO 240/101-76 E Instrucciones De Instalación Y Reglaje página 10

Operator for roll-up doors
SPECIFICATIONS FOR INSTALLATION
The motor must be installed in a space provided with protection so that special tools only are needed for
assembly. This protection will prevent contact with the crumple zone of the door itself. The protection would
not be necessary if the installation is done at a height exceeding 2.7 meters. In case of Dead Man functioning,
the command position must be installed near the gate, in a position to allow the direct and complete
visualization of the same. In case of doors with empty elements, you must verify the absence of fixed structures
near the door, which can create zones of crushing. Photocells or sensors will be installed when required by
applicable laws. The use of photocells or sensors is required when you install more than one centralized
automated door or in case door is automated in an area that is not under direct control.
RULES TO AVOID ACCIDENTS DURING THE MAINTENANCE
Maintenance should be performed only after the motor has been prepared in safety mode. This is achieved by
activating the switch pole, making sure it does not turn off during the maintenance operation (lock, signalling,
etc.).
NOTE TO THE USER
The maintenance or testing of the gear is prohibited to unauthorized personnel.
DESCRIPTION OF THE PRODUCT
Content (Fig. 1). Tools required (Fig. 2)
CONDITIONS OF USE
The EVO range 240 motors are intended for installation of doors winding systems by qualified personnel. The
EVO range 240 motors are designed and constructed for the installation of roller shutters provided with a
compensation system (by springs) according to the weight limits indicated in the table related to the technical
specifications. It is prohibited the use of the motor in applications other than those mentioned above.
TECHNICAL DATAS
TECHNICAL DATAS
Absorbed power
Lifting
Power supply
Current
Nominal torque
Pulley speed
Working temperature
Maximum door travel
Operation time
Weight of the motor
MOUNTING OPERATIONS
Drill in the shutter's central shaft (Fig. 4) one hole Ø 10 mm. in order the operator doesn't turn, and another Ø 12
mm. for the electric wire. If possible, place the operator in the centre of the shutter's shaft in an easy position for
opening the micro-switches lid to make the wire and the regulation of the limit switches. In case of electric brake,
make another drill of Ø 10 mm. for the cable of the manual release.
Open the pulley unscrewing the M10x25 screws remove the plastic roller band without folding it and keep it in a
clean place. Separate the gear-motor's body removing the 4 screws with the 8mm(fig.5A). hexagonal wrench.
Couple the two parts of the gear-motor around the door's shaft and joint them, screwing the 4 screws on the gear-
motor's support(fig.5B). If the tube size is of 101 mm diam., remove de adaptor of 76 mm diam. (see fig. 7).
Tighten the M10x130 screw (Fig. 6 A) entering it into the Ø 10 mm. hole of the shutter's shaft.
Put again the plastic roller band in its place.
Apply again the pulley by coupling the two parts and tighten the screws.
Screw also the M10x50 (Fig. 6 B), bi-motor (fig. 9 B). Pressing on the shaft till the gear-motor is blocked and tighten
the nut.
EVO 240/101-76 EVO 240/101-76 E EVO 240/101-76 BM EVO 240/101-76 BME
600 W
140 Kg. 130 Kg.
II 230 V. 50/60 Hz +-7%
2.8 A.
185 Nm. 175 Nm.
9 Kg.
10 Kg.
1200 W
320 Kg.
5.6 A.
370 Nm.
8 r.p.m.
-20° C +50° C
6 m.
4.5 '
14 Kg.
300 Kg.
350 Nm.
15 Kg.
9