Product Familiarisation; Intended Use - Silverline 442463 Manual De Instrucciones

GB

Product Familiarisation

1. Stop Block
2. Cable
3. Up Limit Lever
4. Down Limit Lever
5. Cable Drum
6. Hook Holder
7. Motor Cover
8. Mounting Bracket
9. Bracket Fastener
10. Emergency Stop Switch
11. Operating Switch
12. Controller
13. Mains Cable
14. Return Pulley
15. Return Pulley Hook
16. Lifting Hook

Intended Use

Electric, mains-powered hoist with push-button remote control for slow, controlled, straight lifting
and lowering of objects up to 500kg max. For non-commercial, light to medium duty use ONLY.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure all parts of the product are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this product
Before Use
WARNING: Ensure the tool is disconnected from the power supply before attaching or changing
any accessories, or making any adjustments.
Hoist installation
WARNING: DO NOT attempt to install this hoist single-handedly. Correct and safe installation
requires more than one person.
1. Locate a suitable installation position for the hoist
Note: The hoist is designed to be installed on a beam of at least 43mm in diameter with a wall
thickness of at least 3mm. Ensure the beam is capable of supporting loads twice the maximum load
capacity of the hoist.
2. Lift the hoist up to the beam and align the Mounting Brackets (8) with the threaded holes on the
top of the Motor Cover (7)
3. Fasten the Mounting Brackets to the Motor Cover securely, using the Bracket Fasteners (9)
Attaching the return pulley
1. Mount the Return Pulley (14) by removing the bolts and the R-Clip securing the Return Pulley
Hook (15)
2. Feed the cable around the roller of the return pulley and attach the main Lifting Hook (16) to the
Hook Holder (6) on the Motor Cover (7) - take care not to lose the bushes securing the Return
Pulley Hook (15)
3. Re-align the Return Pulley Hook and replace the bolts and R-Clip
Note: Ensure the Return Pulley is correctly mounted. When correctly attached the hoist has a lifting
capability of 500kg. When using the Lifting Hook (16) for lifting, the capacity is reduced to 250kg.
The lifting capacity is printed on the side of each hook.
6
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing protection, as well as
suitable gloves, when working with this tool.
• Once plugged into the mains power source, the hoist will be ready for operation
• Never move the Operating Switch (11) directly between
the central (OFF) position between each up or down operation
• If the hoist is unable to lift the load, stop immediately to prevent it being overloaded
Loading the Hoist
• Before loading, ensure the load is placed directly below the hoist. Failure to do so could result in
the load swinging freely once elevated
• Ensure that the load is free to move and is not restricted by anything. If the load is restricted, this will
cause the hoist to overload and potentially cause severe damage. This may also invalidate the warranty
• The load must be firmly and securely attached to the Lifting Hook (16) of the hoist
• If using a cargo sling to aid in the lifting of the load: ensure the sling is sufficiently supporting
the load, and the load is properly centred in the sling
Note: Ensure that the operating switch is in the off position so that the hoist will not attempt to lift
the load whilst being connected.
Lifting the Load
1. When the load is correctly attached, remove the cable slack slowly by moving the Operating
Switch (11) into the position
2. When the slack has been removed, ensure there are no persons within a 5m radius of the load
being lifted
3. Press the operating switch into the to lift the load to its required position
Note: Be aware of the maximum lifting capacities and height limitations stated in the specifications.
• When the hoist reaches its height limitation it will automatically switch off
Lowering the Load
1. Before attempting to lift the load, make sure the surface the load is to be lowered onto is capable
of supporting the load, and that it is sufficiently stable and ready to be loaded
2. Lower the load by pressing the Operating Switch (11) into the
3. Gently lower the load ensuring that the load stabilises
4. Lower the Lifting Hook (16) an extra 30cm to ensure there is enough cable slack to disconnect
the loading hook and then lift the hook clear of the load
Note: When lifting the hook clear, ensure the cable winds onto the spool correctly and does not
cross over itself.
WARNING: If at any point during the hoist's operation someone enters the operating area or
the load becomes unstable, press the Emergency Stop Button (10) immediately. To release the
Emergency Stop Button, rotate it clockwise.
Accessories
• A range of accessories and consumables, including Hoist Support Arm, 1m Cargo Sling 1 Tonne,
2m Cargo Sling 1 Tonne, Safety Hard Hat, and Expert Rigger Gloves, is available from your
Silverline stockist.
• Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any inspection,
maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised Silverline service centre. This advice also applies to extension cords
used with this tool
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the machine's service life. Clean the body of your machine with a soft brush, or dry cloth.
If available, use clean, dry, compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do not use alcohol, petrol or
strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
. The switch must be moved into
position