Cleaning, Maintenance And Ordering Spare Parts - EINHELL TE-CD 12/1 Li-i Manual De Instrucciones Original

6.4 Changeover switch (Fig. 5/Item 3)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. To avoid causing damage to
the gearing, the direction of rotation must only be
changed when the equipment is at a standstill.
When the slide switch is in the middle position,
the On/Off switch is blocked.
6.5 On/Off switch (Fig. 5/Item 4)
Infi nitely variable speed control is possible with
the On/Off switch. The further you push the
switch, the higher the speed of the cordless
screwdriver.
6.6 Switching from speed 1 to speed 2 (Fig.
4/Item 7)
You can work with a higher or lower speed de-
pending on the position of the selector switch.
Change the gear only when the drill is at a stand-
still. If you fail to observe this point, the gearing
may be damaged.
6.7 Battery capacity indicator (Fig. 6 /Item 2)
Press the battery capacity indicator switch (a).
The battery capacity indicator (2) indicates the
charge state of the battery on 3 colored LEDs.
All 3 LEDs are lit:
The battery is fully charged.
The yellow and red LEDs are lit
The battery has an adequate remaining charge.
Red LED is lit:
The battery is empty, recharge the battery.
6.8 LED lamp (Fig. 1/Item 10)
The LED light (10) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED light (10) will come on
automatically as soon as you press the On/Off
switch (4).
Anl_TE_CD_12_1_Li_i_SPK9.indb 22 Anl_TE_CD_12_1_Li_i_SPK9.indb 22
GB
6.9 Changing the bit (Fig. 7)
Caution! Set the changeover switch (3) to its cen-
ter position whenever you carry out any work (for
example changing the tool, maintenance work,
etc.) on the cordless screwdriver.
•
The cordless screwdriver is fitted with a
quick-action chuck (9) with an automatic
spindle stop.
•
Open the chuck (9). The chuck opening (a)
must be large enough to hold the tool (drill bit
or screwdriver bit).
•
Select the suitable tool. Push the tool as far
as possible into the chuck opening (a).
•
Tighten the chuck (9) and then check that the
tool is secure.
6.10 Screwdriving
It is advisable to use self-centering screws (e.g.
Torx, cross recessed head) as these will enable
you to work safely and reliably. Always make sure
that the bit used is of the same size and shape as
the screw. Set the torque to suit the screw size as
specifi ed in the instructions.
7. Cleaning, maintenance and
ordering spare parts
Hazard!
Always pull out the power plug or take out the
rechargeable battery before starting any cleaning
work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
- 22 -
17.10.2019 16:06:25 17.10.2019 16:06:25