Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Designation: Spray gun
How to adjust the spray profile:
Regulate the atomiser air pressure (C)
Regulate the coating substance pressure (only if sub-
stance is fed via pump or pressure container)
Adjust the needle stroke adjuster screw (B) on the
gun
Adjust the width of the spray jet via the flat jet regula-
tor (F) (only with flat jet nozzles)
Choosing the suitable nozzle size
Excessive air pressure not only leads to unnecessarily
high air consumption but also generates heavy misting
of the coating substance. It is advisable to first adjust the
spray profile by adjusting the air and coating material
pressure. If this does not produce a satisfactory profile,
you should experiment with different nozzle sizes.
OPERATIONAL INTERRUPTIONS,
CLEANING
ALWAYS ADHERE TO THE INSTRUCTIONS IN THE
SAFETY DATA SHEET OF THE DETERGENT MANU-
FACTURER. DETERGENTS CAN BE HARMFUL TO
HEALTH AND EASILY FLAMMABLE!
THE SPRAY GUN SHOULD NEVER BE COMPLETELY
IMMERSED IN DETERGENT! THIS COULD DESTROY
THE GASKETS AND RINSE OUT THE LUBRICANT!
DO NOT USE ACIDIC OR ALKALINE MATERIALS
AND/OR DETERGENTS WHEN CLEANING FLOW
CUPS MADE OF ALUMINIUM! DO NOT CLEAN PLA-
STIC CUPS USING HIGHLY SOLVENT DETERGENTS.
The spraying process is terminated by releasing the
trigger
Interrupt feed of coating substance (empty flow cup,
unscrew suction cup, switch off pump or pressure
container)
Clean spray gun (in place of the coating substance,
spray a suitable detergent until it emerges clear and
without soiling)
Interrupt detergent feed
Press trigger to blow out detergent residues
Interrupt the compressed air feed
http://www.krautzberger.com
Type: Perfekt 4
Clean externally using a
cloth soaked in detergent
MAINTENANCE
Please see our catalogue for accessories as well as avai-
lable air nozzles, material nozzles and needles. The
catalogue and spare parts list are available on the Inter-
net in PDF format( www.krautzberger.com ).We would
also be happy to send you a spare parts list on request.
For maintenance and service work, we recommend the
toolbag Perfekt 4 comprising:
2 doubleended OE spanners 17/19, 13/15
1 ring spanner 13/15
2 OE spanners SW 12, SW 7
1 screwdriver
1 tightening pin
1 round/flat brush
1 oilcan
Lightly grease the marked parts (see diagram in Appen-
dix)
ALL MAINTENANCE WORK MUST BE PERFORMED BY
SUITABLY QUALIFIED PERSONNEL!
BEFORE ALL MAINTENANCE WORK:CLEAN SPRAY GUN,
INTERRUPT COMPRESSED AIR FEED AND COATING SUB-
STANCE FEED; DISSIPATE ANY RESIDUAL PRESSURE BY
OPERATING THE AUTOMATIC SPRAY GUN
Check wearing parts like gaskets, nozzles and needles
at regular intervals. The level of wear depends on the
abrasiveness of the coating substance used. Escaping
air and coating substance as well as the deterioration of
the spray profile are signs that parts are worn. Do not
clean material and air nozzles using hard, sharpedged
objects (for cleaning of the nozzles, we recommend our
brush set).The wearing parts are shown in the Appendix.
LIGHTLY GREASE SLIDING PARTS. WE ADVISE YOU TO
USE KRAUTZBERGER SPECIAL GREASE FOR PARTS
THAT NEED GREASING. THIS GREASE IS AVAILABLE IN
250G CANS.
ALWAYS REPLACE MATERIAL NOZZLE AND MATERIAL
NEEDLE TOGETHER
FOLLOWING ASSEMBLY, ENSURE THAT ALL PARTS
ARE FIRMLY TIGHTENED/CONNECTED
CHECK MOVING PARTS FOR SMOOTH MOTION
CHANGING THE AIR AND MATERIAL NOZZLE
LOOSEN MILLED NUT (1)
REMOVE AIR NOZZLE (2)
UNSCREW MATERIAL NOZZLE (3)
OrderNo.:
0660
ENGLISH
11
Tabla de contenido
