Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
WS8975 Vanishing Door/Window Contact
Installation Instructions
Introduction
The WS8975 is a supervised, wireless, door/window contact intended
for use with DSC Alarm systems.
NOTE: This device shall be installed by qualified Service Persons
only.
Specifications
• Dimensions: 57mm×25mm×5.3mm (2.25"×1"×0.21")
• Temperature Range: -10°C to +50°C (14°F to 122°F).
• Humidity: 95 ± 5% (non-condensing)
• Battery: Panasonic Lithium CR2032
• Battery Life: 5 years (NOM)
NOTE: Temperatures below -10°C (14°F) can cause the WS8975
to report a false low battery indication. Operation below -10°C
(14°F), will reduce the battery life significantly.
Battery Installation/Replacement
• Insert a coin (Fig. 1) or a flat head screw driver (Fig. 2) into the
notch indicated and gently twist to open. Lift up and pull the case
outward to open (Fig. 3).
• Insert Battery (Fig. 4) with the + side facing UP .
CAUTION: Observe the correct polarity when installing battery.
Use only Panasonic Lithium CR2032 batteries for replacement.
WARNING! Battery may explode if mistreated. Do not recharge, disassemble or dispose of
in fire.
Installation
NOTE: Select a mounting location free from exposure to moisture and humidity.
• Mount the WS8975 on window or door frame using the supplied double-sided tape or screws
(Fig. 5).
• Find the notch on the outside of the WS8975 enclosure. Align the magnet with the notches
indicated in Fig. 6. Ensure that the distance between magnet and transmitter does not exceed
15.8 mm (5/8").
Enrollment
Follow these enrollment steps for
programming wireless devices on a
PowerSeries Panel.
1. At a system keypad, enter
[*][8][Installer's code][804].
2. Enter the 2-digit number for zone
that the device will be occupying
[01] to [32].
3. Enter the ESN number.
4. To enroll another wireless device
enter another 2-digit zone number
and then ESN number.
5. Press [#] to exit section [804]
when finish.
6. Program
Zone
sections [001] to [004]*
7. Enable wireless attribute (option 8)
in section [101] to [132]*
8. Program the Zone on the correct
partition in section [202] to [265]*
* see panel's Installation Manual for
more detail information.
Compatible Receiver
List
• RF5132-868 MHz
definition
in
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Manuales relacionados para DSC WS8975
Resumen de contenidos para DSC WS8975
- Página 1 • Mount the WS8975 on window or door frame using the supplied double-sided tape or screws (Fig. 5). • Find the notch on the outside of the WS8975 enclosure. Align the magnet with the notches indicated in Fig. 6. Ensure that the distance between magnet and transmitter does not exceed Fig.
- Página 2 REMARQUE : Choisissez un emplacement de montage à l’abri de toute éclaboussure ou humidité. • Montez le WS8975 dans un cadre de fenêtre ou de porte au moyen de l'adhésif double face ou de vis (Fig. 5). • Trouvez l’encoche sur l’extérieur du boîtier du WS8975. Alignez l’aimant avec les fentes Fig.
- Página 3 Instalación NOTA: Seleccione un emplazamiento de montaje no expuesto a la humedad. • Monte el dispositivo WS8975 en el marco de la puerta o la ventana con la ayuda de la cinta o los tornillos de doble cara (Fig. 5).
- Página 4 Installazione NOTA: Selezionare un punto di montaggio che non sia esposto a umidità. • Montare il contatto WS8975 sul telaio della porta o della finestra utilizzando le viti o il nastro bi-adesivo forniti (Fig. 5). • La tacca si trova sull'esterno dell'astuccio del contatto WS8975. Disporre la calamita in linea Fig.