Tabla de contenido
Idiomas disponibles
Idiomas disponibles
2. *DVB-T OUTPUT: DVB-T output
2.1. DVB T Mode:
2K, 8K.
2.2. Q M Mode:
QPSK, 16 Q M, 64 Q M.
2.3. Code Rate:
FEC 1/2, 2/3, 3/4, 5/6, 7/8.
2.4. Guard Interval:
1/4, 1/8, 1/16, 1/32.
2.5. Bandwidth:
6, 7, 8 MHz.
2.6. IQ mode:
normal, Inverted.
3. LNB: LNB supply voltage and configuration
3.1. Input Loop:
Enabl e / Di s abl e the i n put l o op.".
>LNB Polarity:
0V, +13V, +18V, +13V 22KHz, +18V 22KHz.
>DiSEqC Satellite:
OFF, S T , S T B, S T C, S T D.
>DiSEqC Polarity:
OFF, V Low, H Low, V High, V High.
B>LNB Polarity:
0V, +13V, +18V, +13V 22KHz, +18V 22KHz.
B>DiSEqC Satellite:
OFF, S T , S T B, S T C, S T D.
B>DiSEqC Polarity:
OFF, V Low, H Low, V High, V High.
4. **S T INPUT: Satellite input signal
4.1. 1>Input Sel: INPUT / INPUT B
4.2. 1>Freq(MHz):
IF S T 950 ÷ 2150 MHz.
4.3. 1>Baud Rate (MB):
4.4. 1>Init Tuner:
Syncronize the tuner (press
4.5. 2>Input Sel: INPUT / INPUT B
4.6. 2>Freq(MHz):
IF S T 950 ÷ 2150 MHz.
4.7. 2>Baud Rate (MB):
4.8. 2>Init Tuner:
Syncronize the tuner (press
* Default valves in bold.
** This data is shown when the tuner is tuned.
5. OUTPUT SERVICES
- This function is only visible when the tuner is tuned.
5.1. 1>List of Services:
list of services.
Press
to view the list.
G
J
J
Press
to select the service.
L
M
G
Press
to enter the service parameters.
G
–
"+" sign followed by the name of the service indicates
that this service is in the output multiplex.
–
" * " sign before the name indicates an encrypted
service.
5.1.1. ctive:
enables the service on output MUX
J
J
(use
to select and press
L
M
5.1.2. LCN:
llows assigning a LCN (Logical Channel Number)
between 1 and 999 to the services at the output
J
J
(select with
and press
L
M
NO LCN).
5.1.3. Program Number:
indicates the service PN.
5.1.4. Program Nb Edit:
Permits to change the value of the
PN associated with a service between 1 and 65535.
Changing from its initial value should be different for each
J
J
service (select with
L
M
5.2. 2>List of Services:
list of services.
Press
to view the list.
G
J
J
Press
to select the service.
L
M
G
Press
to enter the service parameters.
G
.
1 ÷ 45.
).
OK
.
1 ÷ 45.
).
OK
).
OK
; 0000 stands for
OK
and press
).
OK
–
"+" sign followed by the name of the service indicates
that this service is in the output multiplex.
–
" * " sign before the name indicates an encrypted
service.
5.2.1. ctive:
enables the service on output MUX
J
J
(use
to select and press
L
M
5.2.2. LCN:
llows assigning a LCN (Logical Channel Number)
between 1 and 999 to the services at the output
J
J
(select with
and press
L
M
NO LCN).
5.2.3. Program Number:
indicates the service PN.
5.2.4. Program Nb Edit:
Permits to change the value of the
PN associated with a service between 1 and 65535.
Changing from its initial value should be different for each
J
service (select with
L
5.3. Out 1 MUX BW:
indicates the total % of the output 1
MUX occupied.
5.4. Out 2 MUX BW:
indicates the total % of the output 2
MUX occupied.
5.5. Clear all:
clears all the services selected in the DVB-T
output. "Press
".
OK
5.6. Read Services:
reads the transponder services.
"Press
".
OK
- It is not recommendable to work with the output MUX BW
above 92%, as the services may increase their bitrate during
transmission. (Output MUX BW > 92%: Status LED in yellow).
6. PSI EDIT:
llows the Output's NIT configuration.
6.1. NIT Mode:
Pass-Through / LOC L selection. If local is
chosen, allows modifying the following parameters.
6.2. Network Name:
llows living a name to the network.
6.3. Network ID:
(give the same value as the Orig.Net.ID).
6.4. 1>TS ID:
Some receivers need a different TS ID for
every memorised module (value between 0 and 65535).
2>TS ID.
6.5. Orig. Net. ID:
Original Network Identifier by Country
(see table 3).
6.6. Vr. NIT:
NIT version table.
6.7. Vr. SDT:
SDT version table.
6.8. LCN Mode:
Generic/UK. llows to generate the NIT
according to different standards. (40 by default).
7. C M: access to MMI and C M menus
(STT-TWIN-CI 8000)
7.1. C M Position:
Input 1 or input 2.
7.2. Read MMI:
Open the session with the MMI
(only option available if session is not open).
If the session is open, the last option is read again.
7.3. Close MMI:
Closes the session with the MMI.
It's recommended to close the MMI session once
finished the access.
15
).
OK
; 0000 stands for
OK
J
and press
).
M
OK
Tabla de contenido
