SEVERIN KB 8873 Instrucciones De Uso página 14

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 31
Temperature control
∙ The unit is activated by connecting it to the mains. It is
only switched off completely when the plug is removed
from the wall socket.
∙ The temperature in the refrigerator cabinet can be
adjusted by setting the temperature control.
∙ Turning the control clockwise will decrease the
temperature, while turning it anti-clockwise will increase
it.
∙ We recommend turning the temperature control
initially to a medium setting. After a certain time, the
actual temperature should then be checked with a
thermometer, and adjustments made if necessary.
∙ Following a power interruption, or if the unit has been
switched off on purpose, it may take 3 to 5 minutes
before it switches on again.
∙ Note: In position '0', the cooling function is switched
off, though the appliance is still connected to the
mains.
∙ If you notice frost on the rear wall, the most likely
cause is that the door has been left open for too
long, or that warm food has been placed inside the
refrigerator or that the temperature control has been
set too high.
∙ Liquid or strong-smelling food, or food which is likely
to absorb strong odours (e.g. cheese, fish, butter),
should be stored separately or in hermetically sealed
containers.
∙ Warm food should be left to cool down to room
temperature before being placed in the refrigerator.
∙ Always ensure that the door is properly closed and
that the seal is not obstructed by food stored inside the
cabinet or door.
De-frosting and cleaning
∙ Always remove the plug from the wall socket before
cleaning.
∙ When the build-up of ice has reached a thickness of 2
mm, the unit must be de-frosted.
∙ Turn the temperature control down to '0' and leave the
door open.
Place the drip tray at the centre, at the back edge of the
shelf.
The unit is now defrosting, and the resulting melt-water
is collected at the bottom and in the drip tray.
∙ Warning: do not use any external device or other
means (e.g. heaters or heating fans) to accelerate de-
frosting.
∙ Do not pour water over or inside the unit.
∙ For frequent cleaning we recommend the use of
warm water with some mild detergent. To prevent any
unpleasant odour within the refrigerator, it should be
cleaned about once a month.
∙ Any accessories should be cleaned separately with
soapy water. Do not put them in a dishwasher.
∙ Do not use abrasives or harsh cleaning solutions or any
cleaning agents that contain alcohol.
14
∙ After cleaning, thoroughly clean all surfaces with fresh
water before wiping them completely dry. When re-
inserting the plug into the wall socket ensure that you
have dry hands.
∙ Take care not to remove or damage the rating plate
inside the cabinet during cleaning.
∙ To save energy, the compressor (at the rear) should be
cleaned carefully at least twice a year with a brush or a
vacuum cleaner.
Energy saving tips
∙ The appliance should be set up in a well-ventilated, dry
room.
∙ Do not expose the appliance to direct sunlight, and
do not position it next to any heat sources (radiators,
cookers etc). If this cannot be avoided, however,
suitable insulation must be installed between the heat
source and the unit.
∙ Do not cover the ventilation openings and grilles, and
ensure sufficient air circulation behind the unit.
∙ The compressor (at the rear) should be cleaned at
regular intervals. Accumulated dust causes an increase
in energy consumption.
∙ Warm food should be allowed to cool down before it is
stored inside.
∙ Do not leave the fridge door open for too long when
loading or taking out food.
∙ Do not set a lower-than-necessary temperature. For
detailed information on the temperature settings, please
refer to the section Temperature control.
Trouble-shooting
Certain typical sounds can be heard when the appliance is
switched on. These sounds are:
∙ caused by
the electrical
motor within
the compressor
assembly; during
compressor start-up
the sound level will
be slightly higher for
a limited period of time.
∙ caused by the cooling agent flowing through the circuit.
The following table lists possible malfunctions and their
probable causes and solutions. In the event of operational
problems, check first whether a solution can be found using
this table. If the problem persists, disconnect the appliance
from the mains power and contact our Customer Service
Department.
Tabla de contenido
loading

Este manual también es adecuado para:

Kb 8874Kb 8875Kb 8876

Tabla de contenido