Remote Punch Bass; Operation; Adjusting Gain - Rockford Fosgate Power 350S Instalación Y Funcionamiento

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

L
6dB/Octave Low-Pass
C
6dB/Octave High-Pass
L = Low-Pass (Inductor)
C = High-Pass (Capacitor)
For more information, see your
Authorized Rockford Fosgate Dealer.

REMOTE PUNCH BASS

Mounting and installation
1. Find a location, either under the dash or
near the center console, that gives easy
access to the remote.
2. Using the screws supplied, install the
mounting clip with the tabs towards t
he back.
3. Route the cable for the remote and
connect to both the remote and
amplifed subwoofer.
4. Slip the remote onto the mounting clip
until it snaps into place.
5. Install the decal and knob onto the
remote.

ADJUSTING GAIN

Do the following individually for each channel, or both equally if bridged (mono).
To adjust the gain setting, turn the amplifier gains all the way down. Turn the source unit volume up
until distortion is audible and then turn it down a bit until the distortion is inaudible. This will be
about two thirds all the way up on most source units. Next, turn the amplifier gain setting until once
again distortion is audible and then back it down until the distortion is inaudible. Rockford Fosgate
source units do not distort, so the volume can be used at maximum setting.
NOTE: For a more in depth setting procedure, contact Rockford Technical Support.
Speaker Impedance
Freq.
2 OHMS
Hertz
L
C
80
4.1mH 1000mF
100
3.1mH
800mF
130
2.4mH
600mF
200
1.6mH
400mF
260
1.2mH
300mF
400
.8mH
200mF
600
.5mH
136mF
800
.41mH
100mF
1000
.31mH
78mF
1200
.25mH
66mF
1800
.16mH
44mF
4000
.08mH
20mF
6000
51mH
14mF
9000
34mH
9.5mF
12000
25mH
6.6mF
Mounting
Clip
Knob
Decal
I
NSTALLATION
4 OHMS
L
C
L
8.2mH
500mF
16mH
6.2mH
400mF
12mH
4.7mH
300mF
10mH
3.3mH
200mF
6.8mH
2.4mH
150mF
4.7mH
1.6mH
100mF
3.3mH
1.0mH
68mF
2.0mH
.82mH
50mF
1.6mH
.62mH
39mF
1.2mH
.51mH
33mF
1.0mH
.33mH
22mF
.68mH
.16mH
10mF
.33mH
.10mH
6.8mF
.20mH
68mH
4.7mF
.15mH
51mH
3.3mF 100mH
8 OHMS
C
250mF
200mF
150mF
100mF
75mF
50mF
33mF
26mF
20mF
16mF
10mF
5mF
3.3mF
2.2mF
1.6mF
O
PERATION
9

Hide quick links:

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Power 450sPower 550sPower 750sPower 1050s

Tabla de contenido