Top Panel Features - Numark NDX200 Guia De Inicio Rapido

TOP PANEL FEATURES

1. EJECT – Pressing will open or close the
disc tray on the transport.
designed to play commercially available
CDs and properly burned and finalized CD-
Rs. Due to variances on the specification of
certain CD burners
homemade CDs may not play properly. We
recommend burning CDs at the minimum
speed possible for the best performance.
2. PLAY / PAUSE – Plays or pauses the
track. Pausing the track will create a cue
point at that location (which can be adjusted
with the JOG WHEEL in Search Mode).
3. CUE – During playback, pressing CUE will
return to the most recent point where
playback was started and will pause the
track. Holding down CUE will start
playback from this point, and releasing CUE
will cause it to return to that point and will
pause the track.
paused, you can use the JOG WHEEL to
locate a new cue point.
4. SEARCH – Pressing this button allows you
to use the JOG WHEEL to rapidly scan
through the music. The LED indicator will
be red when Search Mode is active. (Note:
If the JOG WHEEL is not used for five
seconds, Search Mode will be deactivated.)
5. JOG WHEEL – The jog wheel serves many
functions depending on its current mode.
a) If a track is not playing, the JOG
WHEEL will search slowly through a
track's frames.
point, rotate the JOG WHEEL then
begin playback when you have
determined
Press CUE to return to that cue
point.
b) If a track is playing, the JOG WHEEL will temporarily bend the pitch of the track. Rotating the JOG WHEEL
clockwise temporarily speeds it up while rotating it counterclockwise slows it down. This is a useful tool for beat-
matching.
c) When the SEARCH button has been activated, rotating the JOG WHEEL will scan rapidly through the track.
6. TRACK KNOB – Turn this knob to select a track to play.
7. +10 – Press this button to skip through your track listing 10 tracks at a time.
8. PROGRAM – This button helps you create a program – a sequence of tracks to play continuously. To create a
program, press PROGRAM when the CD player is paused. To enter a track into the program, use the TRACK KNOB to
select the desired track then press PROGRAM to enter it. Repeat this process for each track you want to enter (in the
order you want them to play). When you have finished, press PLAY / PAUSE to start playing the program. The tracks
will play in the order you entered them, and "PROGRAM" will be shown on the LCD. To cancel your program as it is
playing, press and hold PROGRAM for three seconds so "PROGRAM" disappears from the LCD.
9. SINGLE – Press this button to toggle between Single Play (the deck will stop at the end of each track) or Continuous
Play (the entire disc will be played without interruption).
10. TIME – Switches the time display between elapsed playing time, remaining time on the track, and total remaining time
on the entire CD.
11. LOOP IN – Sets a new cue point or the start point of a loop (a "Loop In" point) during playback.
12. LOOP OUT – Sets the end point of a loop (a "Loop Out" point) and starts playing the loop. While playing a loop, press
LOOP OUT to release it from the loop and continue normal playback.
13. RELOOP – Plays the track immediately from the beginning of a loop (and reactivates the loop).
14. PITCH – Adjusts the range of the PITCH FADER (±4%, 8%, and 16%) or deactivates it. The current range will be
indicated on the LCD and by different LED colors.
15. PITCH FADER – The pitch can be changed by pressing the PITCH button so a PITCH LED is lit, then moving the sliding
fader. The pitch will not be changed if the PITCH LED is off.
16. PITCH BEND -/+ – You can use these two pitch bend buttons to temporarily adjust the pitch and tempo of the music up
to -/+ 4% from the current pitch setting.
17. LCD – Indicates all the functions, as they are occurring, with the CD.
This unit is
and CDs, some
Also, if the track is
To set a new cue
the proper position.
1
11
6
7
5
3
2
4
17
12 13
4
10
9
8
14
15
16