Personal Safety; Environmental Safety; Cleaning And Disposal - Porter & Cable PCE605 Manual De Instrucciones

hot after prolonged usage.
• Before scraping, check work piece for
nails. If there are nails, either remove them
or set them well below intended finished
surface. Striking a nail with accessory
edge could cause the tool to jump.
• Do not wet sand with this tool. Liquids
entering the motor housing are an electrical
shock hazard.
• Never work in area which is soaked
with a liquid, such as a solvent or water,
or dampened such as newly applied
wallpaper. There is an electrical shock
hazard when working in such conditions
with a power tool and heating of the liquid
caused by scraping action may cause
harmful vapors to be emitted from work
piece.
• Do not use sandpaper intended for larger
sanding pads. Larger sandpaper will extend
beyond the sanding pad causing snagging,
tearing of the paper or kick-back. Extra
paper extending beyond the sanding pad
can also cause serious lacerations.
WARNING:
glasses. Everyday eyeglasses are NOT
safety glasses. Also use face or dust mask.
ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CPA
Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NOSH/OSHA respiratory protection.
WARNING:
power sanding, sawing, grinding, drilling, and
other construction activities contains
chemicals known to the state of California to
cause cancer, birth defects or other
reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed
to filter out microscopic particles.
• Avoid prolonged contact with dust from
power sanding, sawing, grinding, drilling,
and other construction activities. Wear
protective clothing and wash exposed
areas with soap and water. Allowing dust
to get into your mouth, eyes, or
the skin may promote absorption of harmful
chemicals.
WARNING:
ALWAYS use safety
Some dust created by
Use of this tool can
generate and/or disperse dust, which may
cause serious and permanent respiratory or
other injury. Always use NOSH/OSHA
approved respiratory protection appropriate for
the dust exposure. Direct particles away from
face and body.
WARNING:
personal hearing protection that conforms
to ANSI S12.6 (S3.19) during use. Under
some conditions and duration of use, noise
from this product may contribute to hearing
loss.
PRECAUTIONS TO TAKE
WHEN SANDING PAINT
1. Sanding of lead based paint is NOT
RECOMMENDED due to the difficulty of
controlling the contaminated dust. The
greatest danger of lead poisoning is to
children and pregnant women.
2. Since it is difficult to identify whether
or not a paint contains lead without a
chemical
recommend the following precautions
when sanding any paint:

PERSONAL SAFETY

1. No children or pregnant women should
enter the work area where the paint
sanding is being done until all clean up
is completed.
2. A dust mask or respirator should be
worn by all persons entering the work
area. The filter should be replaced daily
or whenever the wearer has difficulty
breathing. See your local hardware
store for the proper N.I.O.S.H. approved
dust mask.
3. NO EATING, DRINKING or SMOKING
should be done in the work area to
prevent ingesting contaminated paint
particles. Workers should wash and
clean up BEFORE eating, drinking
or smoking. Articles of food, drink, or
smoking should not be left in the work
area where dust would settle on them.

ENVIRONMENTAL SAFETY

1. Paint should be removed in such a
manner as to minimize the amount of dust
generated.
2. Areas where paint removal is occurring
should be sealed with plastic sheeting of 4
mils thickness.
3. Sanding should be done in a manner
to reduce tracking of paint dust outside
the work area.

CLEANING AND DISPOSAL

lay on
1. All surfaces in the work area should be
vacuumed and thoroughly cleaned daily
for the duration of the sanding project.
4
Always wear proper
analysis, we