NSS CXC 200 Manual Del Usuario página 3

FIG G. 3: Top p Detail
Control
panel
CXC C 200, CX H 200, & C
OPE ERATING INSTRUC
1. P Pre-mix clean ning solution w
separate cont s tainer. Pour m
solution tank o s of the machin
ORTANT: Foa am in the reco
IMPO
mois sture, carpet fi fiber and othe
the v vacuum system m. Use a low
defoa amer to the re ecovery tank
defoa amer manufa cturer instruc
appli ication. Dama age caused by
void the product w warranty.
2. C Connect vacu uum and solut
attach to extra a action wand o
3. I nsert both co rds into sepa
outlets on sep o parate circuits
c cleaning path .
4. S Select vacuum m control - on
5. T Turn on soluti on pump. * S
6. If f desired, turn n on heater (H
7. B Begin cleanin g. Follow indu
p procedures.
8. S Solution press sure on the C
with the press w sure regulator
t he pressure g gauge to ensu
CAU TION: When the recover
an au utomatic floa at valve bloc
Fig. 7 7) and the va acuum moto
pitch hed noise. W When this occ
be tu urned off imm mediately to
vacu uum motors.
9. W When the job is complete,
li iquid from the e solution tank
ensure no det e tergents or rin
t ank.
Manual l 4094131 (Rev. 1122 211)
All manuals and user guides at all-guides.com
Cord
wrap
Solut tion
tank k fill
hole
CXH 500
CTIONS
with hot water r in a
mixed solution n into the
ne.
overy tank ca an allow
r debris to be e drawn into
w-foam deterg ent. Add a
if foaming oc curs. Follow
ctions for prop per
y moisture or r debris will
tion hoses to machine and
or hand tool.
rate, 3-prong grounded
s. Keep cords clear of your
ne or two vacu uums.
See NOTICE, below.
H units only).
ustry-approve ed
CXH 500 may be adjusted
r knob (Fig. 2, , G). Monitor
ure pressure is adequate.
y tank reach hes capacity,
cks vacuum i intake (see
rs will make a high
curs, the mac chine should
prevent dam mage to the
vacuum out a any remaining
k. Rinse with clear water to
nse agents re main in the
FI IG. 4:
Sol lution Pump
filt er location.
Rin nse clean
afte er each use.
10. Empty and ri
help to preve
and reduce t
11. Turn on both
for 3–5 minut
the vacuum m
NOT TICE: At time
prim ming in order
pum mp, insert the
in th he rear pock
the solution hos
solu ution tank an
mom ments, the p
whe en steady wa
use e.
For maintenance
r
TIP: : To empty th
hose e from wand
tank k.
FIG G. 5:
d
Remove the P
and vacuum i
g
and clean afte
o
3
nse the waste e tank thorou
ent the format tion of damag
he growth of odor-causing
h vacuum mot tors and allow
tes to help re emove any mo
motors and a ssure long va
es the soluti on pump ma
r to operate properly. To
e male quick k-connect fitt
ket of the uni t) into the wa
se. Place the e end of the h
nd start the p pump. After a
ump will dis charge exce
ater flow exis sts, the unit
e instructions, see "Mainten
he solution tan nk, remove th
and extract th he solution fro
PVC elbow
inltet filter
er each use.
ughly. This wil l
ging deposits
g bacteria.
w them to run
oisture from
acuum life.
ay require
o prime the
ting (shipped d
and end of
hose into the e
a few
ess air and
is ready for
nance," p. 5.
he vacuum
om solution