Before Putting Into Operation; Assembly - Manupro MPSCST255MM Manual Del Usuario

m WARNIG: The noise emission values can vary
from the specified values during the actual use of the
electric tool, depending on the type and the manner
in which the electric tool is used, and in particular
the type of workpiece being processed. Implement
measures to protect against noise nuisance. In doing
so, take into account the complete working process,
including the times when the electric tool is working
without load or switched off. Suitable measures in-
clude regular maintenance and care of the electric
tool and the insertion tools, regular breaks as well as
proper planning of the working process.

8. Before putting into operation

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans -
port damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
• The machine must be securely installed, i.e. bolted
down on a workbench, base frame or similar.
• Before the machine is put into operation, all covers
and safety devices must be properly attached.
• The saw blade must be able to move freely.
• In the case of wood which has already been worked
with, check for foreign bodies such as nails or
screws etc.
• Before pressing the on/off switch, make sure that
the saw blade is correctly attached and that moving
parts are free-running.
• Before connecting the machine, check that the data
on the type plate matches those of the mains system.
• The machine must only be connected to a properly
installed safety socket which is protected by a fuse
of at least 16A.

9. Assembly

m Warning! Risk of injury!
Improper installation of the circular table saw may re-
sult in serious injury.
Before commissioning, properly and completely in-
stall the circular table saw, including all covers and
safety devices.
Never plug the mains plug into the power outlet be-
fore completing the installation.
If connections are secured with a hexagon screw, nut,
spring washer and washer, the washer and spring
washer must be fitted under the hexagon screw. The
spring washer always lies directly on the (inner) hex-
agon screw or nut.
Hexagon screws must each be inserted from outside
inwards, and the connections must be secured from
the inside with nuts. During assembly nuts and screws
must only be tightened until hand-tight, so that they
cannot fall out. If you tighten the nuts and screws fully
before final assembly, the circular table saw cannot
be erected in a correct and stable manner.
9.1 Assembling the frame and table width extend-
er (Fig. 4-10)
1. Turn the table circular saw over and place it on
the floor.
2. Loosely tighten the table width extender (6) on the
saw table (1) using the hexagon bolts (a), washer
(c), spring washer (d) and nuts (e). (Fig. 6)
3. Screw the four legs (19) and the table supports (24)
onto the housing. (Fig. 7)
4. Loosely tighten the table supports (24) on the
table width extender (6) using hexagon bolts (a),
washer (c), spring washer (d) and nuts (e). Loose-
ly tighten the four legs (19) and table supports (24)
onto the housing using the hexagonal bolts (a).
5. Now loosely screw the four central struts (20a,20b)
with the legs (19) using the carriage bolts (b),
washer (c), spring washer (d) and nuts (e). (Fig. 8)
6. Screw the stand brackets (22) to the holes in the
rear stand legs (19). Assembly material: 2 car-
riage bolts (b), washers (c), spring washers (d)
and nuts (e). (Fig. 9)
ATTENTION: Both stand brackets (22) must be
attached to the rear of the machine at the fixing
points (23). (Fig. 9)
7. Align the table width and length extension lush
with the saw table.
8. Next, tighten all the screws of the legs (19) and
the table width extender (6).
9. Now attach the rubber feet (21) to the legs (19)
(Fig. 10).
10. Place the table circular saw on the base frame (11).
9.2 Insert guide rail (Fig. 11+12)
1. Mount the carriage bolts (b) in the holes provided
in the worktable and the table extensions (6) by
securing them from behind with the flange nuts (e).
2. Loosely tighten the flange nuts (e).
3. Connect both guide rails (15, 15a).
4. Slide the connected reails over the guide groove
on the back over the carriage bolts (b) until they
are centred on the table surface.
GB | 35