Intended Use; General Safety Warnings - Ryobi RBC430SESD Manual De Utilización

Safety, performance, and dependability have been
given top priority in the design of your grass trimmer/
brushcutter.

INTENDED USE

The product is only intended for use outdoors in a well
ventilated area.
For safety reason, the product must be adequately
controlled by using two-handed operation.
The product is intended for cutting long grass, pulpy weed,
or brush and similar vegetation at or about ground level.
The cutting plane should be approximately parallel to the
ground surface. The product should not be used to trim
hedges, bushes, or other vegetation where the cutting
plane is not parallel to the ground surface.
WARNING
When using the product, the safety rules must be
followed. For your own safety and that of bystanders,
please read these instructions before operating the
product. Please keep the instructions safe for later use.

GENERAL SAFETY WARNINGS

■ For safe operation, read and understand all instructions
before using the product. Follow all safety instructions.
Failure to follow all safety instructions listed below, can
result in serious personal injury.
■ Some regions have regulations that restrict the use of
the product. Check with your local authority for advice.
■ Do not allow children or untrained individuals to use
the product.
■ Never start or run the engine in a closed or poorly
ventilated area; breathing exhaust fumes can kill.
■ Clear the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire,
or string, which can be thrown or become entangled in
the string head or blade.
■ Wear full eye and hearing protection while operating
this product. If working in an area where there is a risk
of falling objects, head protection must be worn.
■ Hearing protection may restrict the operator's ability to
hear warning sounds, pay particular attention to
potential hazards around and inside the working area.
■ Wear heavy long trousers, non-slip protective
footwear and gloves. Do not wear loose fitting
clothing, short trousers, jewellery of any kind, or use
with bare feet.
■ Secure long hair so it is above shoulder level to
prevent entanglement in any moving parts.
■ Keep all bystanders, children, and pets at least 15 m
away. Stop the product if anyone enters the area.
All manuals and user guides at all-guides.com
English (Original instructions)
■
■
■
■ Keep all parts of your body away from any moving part.
■ Do not touch area around the silencer or cylinder of the
■ Always
■ Do not smoke when mixing fuel or filling fuel tank.
■ Mix and store fuel in a container approved for fuel.
■ Mix fuel outdoors where there are no sparks or flames.
■ Stop the engine and allow to cool before refuelling or
■ Allow the engine to cool; empty the fuel tank and
■ Always stop the engine and make sure all moving
Never use cutting means or attachments which are not
specified by Ryobi in this manual. This includes the
use of metal multi-piece pivoting chains and flailblades.
These items are known to break up during use and
present a high risk of serious injury to the operator or
bystanders.
Inspection after dropping or other impacts: Thoroughly
inspect the product and identify any problems or damage
to it. Any part that is damaged should be properly
repaired or replaced by an authorised service centre.
16
Do not operate this unit when you are tired, ill, or
under the influence of alcohol, drugs, or medication.
Do not operate in poor lighting. The operator needs
clear unrestricted vision to identify potential hazards.
Keep firm footing and balance at all times. Do not
overreach. Overreaching can result in loss of balance
or exposure to hot surfaces.
product, these parts get hot from operation.
stop the engine
adjustments.
Wipe up any fuel spillage. Move 9 m away from
refueling site before starting engine.
storing the unit.
secure the unit from moving before transporting in a
vehicle.
parts have come to stop before:
● servicing
● leaving the product unattended
● cleaning your product
● changing accessories
● clearing blockages
● checking for any damage after hitting an object
● checking for any damage if the product starts to
vibrate abnormally
● performing maintenance
● removing blade
● installing blade
WARNING
WARNING
before making any